557718
5
Zoom out
Zoom in
Previous page
1/72
Next page
3
English
1 STANDBY/ON switch/indicator
This switch is used to set the MX-D1 to on or standby. A small amount of power is used in standby mode.
When the MX-D1 is turned on, this indicator lights blue and the MX-D1 is ready for use.
When the internal temperature rises, this indicator lights blue and purple alternately. If this happen, relocate this unit in a
well ventilated place and turn down the volume of the pre-amplifier etc.
When a fault is detected, the MX-D1’s protection system activates and this indicator lights red. If this happens,
set the MX-D1 to standby mode immediately and disconnect the AC power cable from the AC outlet.
If the indicator continues to light red when you re-connect the AC power cable, contact the nearest Yamaha dealer.
2 SPEAKER terminals
These terminals are for connecting your speakers.
They provide a reliable connection even with really
thick cables. Be sure to connect the left and right
channels, and the speaker polarities (+/-) correctly.
You can connect speakers with impedance of between
4 to 8 ohms.
3 BALANCE jacks
If your source component has balanced XLR output
jacks, connect them to these jacks using XLR cables.
4 MUTE button
You can temporarily mute the output from the MX-D1
by holding down this button. If you need to change
any input connections while the MX-D1 is still on,
hold down this button while you do it. This will
protect your speakers against possible damage due to
sudden loud noises, thumps, and clicks.
5 UNBALANCE jacks
If your source component has unbalanced RCA jacks
(labeled “AUDIO OUTPUT” on the YPC-1), connect
them to these jacks using an audio pin cable.
6 UNBAL/BAL switch
With this switch you can select the BALANCE jacks
or the UNBALANCE jacks.
7 AC IN connector
Connect the supplied AC power cable here.
e POWER switch
(Australia, U.K., Europe, China and Korea models)
Normally, set this switch to the ON position to use the
MX-D1.
To cut off the power supply from the AC line, set this
switch to the OFF position.
8 RS-232C terminal
9 AMP ID switch
0 CONTROL IN jack
q CONTROL OUT jack
w POWER/THROUGH switch
These are for control expansion. Consult your dealer
for details.
01-MX-D1_GB_E.fm Page 3 Wednesday, October 22, 2003 2:05 PM
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MX-D1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MX-D1 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 4,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info