571272
183
Zoom out
Zoom in
Previous page
1/300
Next page
About MIDI
183
Owner’s Manual
Basic Structure
Release Time (Control #072)
Messages which adjust the AEG release time set for each
Part.
The value set here is an offset value which will be added to or
subtracted from the voice data.
Attack Time (Control #073)
Messages which adjust the AEG attack time set for each Part.
The value set here is an offset value which will be added to or
subtracted from the voice data.
Brightness (Control #074)
Messages which adjust the filter cutoff frequency set for each
Part.
The value set here is an offset value which will be added to or
subtracted from the voice data. Lower values result in a softer
sound.
Depending on the voice, the effective range may be narrower
than the range available for adjustment.
Decay Time (Control #075)
Messages which adjust the AEG decay time set for each Part.
The value set here is an offset value which will be added to or
subtracted from the voice data.
Effect1 Depth (Reverb Send Level) (Control #091)
Messages which adjust the send level for the Reverb effect.
Effect3 Depth (Chorus Send Level) (Control #093)
Messages which adjust the send level for the Chorus effect.
Data Increment (Control #096)
Decrement (Control #097) for RPN
Messages which increase or decrease the MSB value of pitch
bend sensitivity, fine tune, or coarse tune in steps of 1. You will
need to assign one of those parameters using the RPN in the
external device in advance. The data byte is ignored. When
the maximum value or minimum value is reached, the value
will not be incremented or decremented further. (Incrementing
the fine tune will not cause the coarse tune to be
incremented.)
NRPN (Non-Registered Parameter Number)
LSB (Control #098) (Plug-in Board only)
NRPN (Non-Registered Parameter Number)
MSB (Control #099) (Plug-in Board only)
Messages which adjust a voice’s vibrato, filter, EG, drum
setup or other parameter settings.
First send the NRPN MSB and NRPN LSB to specify the
parameter which is to be controlled. Then use Data Entry
(page 182) to set the value of the specified parameter.
Note that once the NRPN has been set for a channel,
subsequent data entry will be recognized as the same
NRPN’s value change. Therefore, after you use the NRPN, you
should set a Null (7FH, 7FH) value to avoid unexpected
results.
For details, refer to the owner’s manual of the relevant Plug-in
Board.
RPN (Registered Parameter Number) LSB (Control #100)
RPN (Registered Parameter Number) MSB (Control #101)
Messages which offset, or add or subtract values from a
Part’s pitch bend sensitivity, tuning, or other parameter
settings. First send the RPN MSB and RPN LSB to specify the
parameter which is to be controlled. Then use Data
Increment/Decrement (page 183) to set the value of the
specified parameter. Note that once the RPN has been set for
a channel, subsequent data entry will be recognized as the
same RPN’s value change. Therefore after you use the RPN,
you should set a Null (7FH, 7FH) value to avoid unexpected
results.
The following RPN numbers can be received.
Channel Mode Messages
The following Channel Mode Messages can be received.
All Sounds Off (Control #120)
Clears all sounds currently sounding on the specified
channel. However, the status of channel messages such as
Note On and Hold On is maintained.
Reset All Controllers (Control #121)
The values of the following controllers will be reset to the
defaults.
All Notes Off (Control #123)
Clears all notes currently on for the specified channel.
However, if Hold1 or Sostenuto is on, notes will continue
sounding until these are turned off.
RPN MSB RPN LSB PARAMETER
00 00 Pitch Bend Sensitivity
00 01 Fine Tune
00 02 Coarse Tune
7F 7F Null
2nd BYTE 3rd BYTE MESSAGE
120 0 All Sounds Off
121 0 Reset All Controllers
123 0 All Notes Off
126 0 - 16 Mono
127 0 Poly
CONTROLLER VALUE
Pitch Bend Change 0 (center)
Aftertouch 0 (off)
Polyphonic
Aftertouch 0 (off)
Modulation 0 (off)
Expression 127 (max)
Hold1 0 (off)
Portamento 0 (off)
Sostenuto 0 (off)
Soft Pedal 0 (off)
Portamento Control Cancels the Portamento source key number
RPN Number not specified; internal data will not change
NRPN Number not specified; internal data will not change
183


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MOTIF ES7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MOTIF ES7 in the language / languages: English as an attachment in your email.

The manual is 8,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha MOTIF ES7

Yamaha MOTIF ES7 Installation Guide - English - 35 pages

Yamaha MOTIF ES7 Installation Guide - German - 35 pages

Yamaha MOTIF ES7 User Manual - German - 300 pages

Yamaha MOTIF ES7 User Manual - Dutch - 300 pages

Yamaha MOTIF ES7 User Manual - French - 300 pages

Yamaha MOTIF ES7 Installation Guide - French - 35 pages

Yamaha MOTIF ES7 User Manual - Italian - 308 pages

Yamaha MOTIF ES7 Installation Guide - Italian - 12 pages

Yamaha MOTIF ES7 User Manual - Portuguese - 300 pages

Yamaha MOTIF ES7 User Manual - Spanish - 297 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info