652605
69
Zoom out
Zoom in
Previous page
1/86
Next page
MONTAGE Owner’s Manual
59
Troubleshooting
Are the volume or expression settings too low?
In case of Normal Part (AWM2) and Drum Part
In case of Normal Part (FM-X)
Are the parameter settings such as Element Switch, Note Limit, Velocity Limit, and Velocity Offset appropriate?
In case of Normal Part (AWM2) and Drum Part
In case of Normal Part (FM-X)
Is the Mute switch for each Element/Operator of Part turned on?
In case of Normal Part (FM-X), is the Carrier Level is set to “0”?
Is the output parameter of each Part turned off?
No sound from the A/D INPUT jack.
Is the switch of the microphone turned on?
Check the microphone type. Make sure to use a dynamic microphone.
Is the cable between the microphone or audio equipment and this instrument properly connected?
Is the A/D INPUT [GAIN] knob turned to the minimum?
Is the A/D INPUT [ON/OFF] button turned on?
Check whether or not the connection status of the A/D INPUT [L/MONO]/[R] matches the “Mono/Stereo” parameter.
Check whether or not the “Mic/Line” parameter is set to the appropriate value.
When the output level of the connected equipment (such as a microphone) is low, set this parameter to “Mic.” When the
output level of the connected equipment (such as a synthesizer keyboard, CD player) is high, set this parameter to “Line.”
Are the volume settings of the A/D Input Part too low?
Are the effect settings appropriate?
Is the output setting of the A/D Input Part set appropriately?
Check whether or not the Vocoder Effect is selected.
When Vocoder is selected as the Insertion Effect for the current Part, the audio signal input from the A/D INPUT [L/MONO]/[R]
jacks may not produce any sound depending on the parameter settings.
[UTILITY] [Settings] [Sound] Tone Generator “Volume
[EDIT] PART [COMMON] [General] “Volume
[EDIT] Part selection ELEMENT/OPERATOR [COMMON] [Part Settings] [General] “Volume
[EDIT] Part selection ELEMENT/OPERATOR [COMMON] [Part Settings] [General] “Dry Level”
[EDIT] Part selection Element/Key selection [Amplitude] [Level/Pan] “Level”
[EDIT] Part selection Operator selection [Level] “Level”
[EDIT] Part selection ELEMENT/OPERATOR [COMMON] [Part Settings] [General]
[EDIT] Part selection Element/Key selection [Osc/Tune]
[EDIT] Part selection ELEMENT/OPERATOR [COMMON] [Part Settings] [General]
[EDIT] Part selection Mute Switch of each Element/Operator
[EDIT] Part selection Operator selection [Level] “Level”
[EDIT] Part selection ELEMENT/OPERATOR [COMMON] [Part Settings] [General] “Part Output”
[EDIT] PART [COMMON] [Audio In] [Mixing] A/D In “Input Mode”
[UTILITY] [Settings] [Audio I/O] A/D Input”
[EDIT] PART [COMMON] [Audio In] [Mixing] A/D In “Volume
[EDIT] PART [COMMON] [Audio In] [Routing]
[UTILITY] [Settings] [Audio I/O] Output
[EDIT] Part selection ELEMENT/OPERATOR [COMMON] [Effect] [Routing]
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha Montage 8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha Montage 8 in the language / languages: English as an attachment in your email.

The manual is 14,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info