Manual Yamaha MG16XU (page 31 of 40) (English)

655877

Zoom out

Zoom in

1/40

MG20XU/MG20/MG16XU/MG16/MG12XU/MG12 Owner’s Manual

Troubleshooting

Other

If any specific problem should persist, please contact your Yamaha dealer.

 The power does not come

on.

 Is the mixer connected to an independent power source (generator, etc.) or a power strip with

switches? Check that the power of that device is turned on.

 No sound is output.  Are external instruments (including microphones) and speakers connected correctly?

 Are your cables shorted?

 Are the [GAIN] knobs for each channel, channel faders, [STEREO] master fader, and [GROUP] fad-

ers adjusted to appropriate levels?

 Are the bus assign switches and [LINE /USB ] switch set appropriately?

 No sound is output from the

[STEREO OUT] jack.

 Are the [ON] switch and [ST] switch for the channels you are using turned on?

 Is the [STEREO] master [ON] switch turned on?

 No sound is output from the

[SEND (AUX1 – 4)] jacks

 Are the [SEND MASTER] knobs and [AUX 1 – 4] for each channel set appropriately?

 Are the [ON] switches for the channels you are using turned on?

 No sound is output from the

[MONITOR OUT] jack or

[PHONES] jack.

 Are the [PFL] switches for the channels you are not using turned on?

Turn the [PFL] switches off.

 The sound is low, distorted,

or noisy.

 Is the microphone connected to a [MIC] jack or a [MIC/LINE] jack?

 When using a condenser microphone, is the [PHANTOM +48V] switch turned on?

 Is the [PAD] switch on? Turn this switch off for sources with low output levels, such as microphones.

 Is the output signal level for the instrument connected to the mixer appropriate?

 When connecting an instrument with an output level of +4 dBu, either turn on the [PAD] switch on a

mono input channel or use a stereo input channel.

 Where an input channel provides both a XLR input jack and a phone input jack, or a phone input

jack and an RCA pin jack, are there connections made at both jacks? Use only one of these jacks.

 Are the [GAIN] knobs for each channel, channel faders, [STEREO] master fader, and [GROUP] fad-

ers adjusted to appropriate levels?

 Are effect or compressor levels too high? Use the [FX] knob, [FX RTN] fader, [FX RTN LEVEL]

knob, and [COMP] knob to lower their levels.

 Effects are not applied.  Are the [FX] knobs for each channel adjusted to appropriate levels?

 Is the [ON] button for [FX RTN] turned on?

 Are the [PARAMETER] knob and [FX RTN] fader adjusted to appropriate levels?

 Is the [FX RTN] bus assign switch set appropriately?

 If external effects are connected to the [SEND(AUX1 – 4)] jacks, are the [AUX1 – 4] knobs for

[SEND MASTER] set appropriately?

 Speaking voices are not

clear.

 Is the [HPF] switch turned on?

 Is the equalizer ([HIGH]/[MID]/[LOW]) adjusted appropriately?

 No mixer monitor signal is

output.

 Are powered speakers connected to the [MONITOR OUT] jacks?

Use the [MONITOR LEVEL] knob to adjust the signal output from the [MONITOR OUT] jacks.

 Left and right levels are dif-

ferent for a stereo signal

input.

 Is [PAN] set to the center? If panned to the center, try reversing the left and right input connections.

If, after switching the left and right connections, the side with the low volume level also switches,

check the instrument or device that is the source of the signal.

 Are you using the same type of cable to connect both the left and right input signals? Cables with

built-in resistors will attenuate the signal.

 The sound level is unstable

and inconsistent.

 Is the compressor level set too high? Use the [COMP] knob to lower the level.

 The volume of audio play-

back from a computer need

to be adjusted.

 Use the “Attenuator Function”. For details, see page 28.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MG16XU in the language / languages: English as an attachment in your email.

The manual is 5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha MG16XU

Yamaha MG16XU User Manual - German - 40 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yamaha MG16XU Manual

Product: