462455
15
Zoom out
Zoom in
Previous page
1/24
Next page
Front & Rear Panels
MG124CX/MG124C Owner’s Manual
15
Reference
8 PHONES Jack
Connect a pair of headphones to this stereo phone jack. The
PHONES jack outputs the same signal as the MONITOR
OUT jacks.
9 PHANTOM +48 V Switch
This switch toggles phantom power on and off. When the switch
is on the mixer supplies +48V phantom power to all channels
that have XLR mic input jacks (CHs 1–4, 5/6, 7/8).
Turn this switch on when using one or more phantom-pow-
ered condenser microphones.
When this switch is on the mixer supplies DC +48 V
power to pins 2 and 3 of all XLR-type MIC INPUT
jacks.
0 RETURN
•AUX (AUX1) Control
Adjusts the level at which the L/R signal received at the
RETURN jacks (L (MONO) and R) is sent to the AUX
(AUX2) bus.
STEREO Control
Adjusts the level at which the signal received at the
RETURN jacks (L (MONO) and R) is sent to the STEREO
L/R buses.
If you supply a signal to the RETURN L (MONO)
jack only, the mixer sends the same signal to both the
L and R Stereo buses.
A Master SEND
•Master AUX (AUX1) Control
Adjusts the signal level sent to the AUX (AUX1) SEND jack.
•Master EFFECT (AUX2) Control
Adjusts the level of the signal sent to the EFFECT (AUX2)
bus.
If you are using the MG124CX, the Master EFFECT
control does not affect the level of the signal sent
from the EFFECT bus to the internal digital effect
processor.
B POWER Indicator
This indicator lights when the mixer’s power is ON.
C Level Meter
This LED meter displays the level of the signal selected by
the MONITOR switch
D, 2TR IN switch E and PFL
switch. The “0” segment corresponds to the nominal output
level. The PEAK segment lights red when the output reaches
the clipping level.
D MONITOR/PHONES
MONITOR Switch
If this switch is set to GROUP ( ), the Group 1/2 bus sig-
nals are sent to the MONITOR OUT jacks, the PHONES
jack, and the level meter. If it is set to STEREO ( ), the
STEREO L/R bus signals are sent to these jacks and the level
meter.
MONITOR Control
Controls the level of the signal output to the PHONES jack
and the MONITOR OUT jacks.
E 2TR IN
2TR IN Switch
If this switch is set to TO MONITOR ( ), the signals input
via the 2TR IN jacks are sent to the MONITOR OUT jacks,
the PHONES jack, and the level meter. If it is set to TO STE-
REO ( ), the signals are sent to the STEREO L/R buses.
2TR IN control
Adjusts the level of the signal sent from the 2TR IN jacks to
the STEREO L/R buses.
The following illustration shows how the switch settings cor-
respond to the signal selection.
* : When overdubbing, you can adjust the levels of the
monitor playback signal and the signal being recorded separately.
MONITOR MIX Signal Flow
If the input channel PFL switch is on ( ), then only
the PFL output from that channel is sent to the C-R
OUT jacks, PHONES jacks, and level meter.
F GROUP 1-2 Fader
Adjusts the signal level sent to the GROUP OUT jacks.
G ST Switch
If this switch is on ( ), the signals are sent to the STEREO
L/R buses via the GROUP 1-2 fader
F
. The Group 1 signal
goes to Stereo L and the Group 2 signal goes to Stereo R.
H STEREO OUT Master Fader
Adjusts the signal level sent to the STEREO OUT jacks.
Be sure to leave this switch off ( ) if you do
not need phantom power.
When tuning the switch on ( ), be sure that
only condenser mics are connected to the
XLR input jacks (CHs: 1 to 7/8). Devices
other than condenser mics may be damaged if
connected to the phantom power supply. Note,
however, that the switch may be left on when
connecting to balanced dynamic microphones.
To avoid damage to speakers, be sure to turn
off amplifiers (or powered speakers) before
turning this switch on or off. We also recom-
mend that you turn all output controls (STE-
REO OUT Master Fader, GROUP 1-2 Fader,
etc.) to their minimum settings before operat-
ing the switch to avoid the risk of loud noises
that could cause hearing loss or device damage.
NOTE
CAUTION
NOTE
NOTE
Switches
Signals output via the
MONITOR/PHONES
jacks
PFL
MONITOR/
PHONES
2TR IN
ON
PFL
OFF
STEREO
TO STEREO
STEREO (+ 2TR IN)
TO MONITOR
STEREO + 2TR IN
*
GROUP
TO STEREO
GROUP
TO MONITOR
GROUP (+ 2TR IN)
Playback
signal
Recording
signal
2TR IN
2TR IN Control
STEREO OUT Master Fader
MONITOR/PHONES Controls
STEREO
buses
REC OUT
MONITOR/
PHONES
jacks
NOTE
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha MG124C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha MG124C in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info