157308
68
Zoom out
Zoom in
Previous page
1/75
Next page
Appendix
69
Troubleshooting
Problem
Auto Configuration
does not appear to
work correctly.
The MusicCAST client
does not output any
sound.
You cannot start
playback on the
MusicCAST client.
Playback from the
MusicCAST client
skips.
Cause
The network is not configured correctly.
The network signal is weak (for wireless
network connections only).
Either the MusicCAST server or the
MusicCAST client is not set to Auto
Configuration mode.
The MusicCAST server is storing songs
or recording.
The volume setting of the MusicCAST
client is low.
The MusicCAST client is not correctly
connected to speakers.
Auto Configuration is not complete.
The network is not configured correctly.
The MusicCAST server is turned off.
The hard disk drive in the MusicCAST
server does not contain any songs that
have been completely encoded to MP3
format.
When the MusicCAST server is set to
distribute MP3 files to your MusicCAST
client, the MusicCAST client displays a
*
beside songs which the MusicCAST
server has not converted to MP3 format.
The network signal is weak (for wireless
network connections only).
The network signal is weak (for wireless
network connections only).
The network is extremely congested (for
wired network connections only).
Remedy
Check the network settings of the MusicCAST client
and MusicCAST server.
Try changing the network channel or the location of
the MusicCAST client, or alternatively changing to a
wired network connection.
Check the configuration procedure and try again.
Stop recording and start the Auto Configuration
process again.
Increase the volume setting.
Check the connections between the MusicCAST
client and the speakers.
Run the Auto Configuration process.
Check the network settings of the MusicCAST client
and MusicCAST server.
Turn the MusicCAST server on.
Wait until the MusicCAST server completes
encoding songs to MP3.
Register songs stored from external components to
the library, or wait for the MP3 encoding process to
complete.
The
*
displayed beside PCM-only songs disappears
when encoding is complete.
Try changing the network channel or the location of
the MusicCAST client, or alternatively changing to a
wired network connection.
Try changing the network channel or the location of
the MusicCAST client, or alternatively changing to a
wired network connection.
Place your MusicCAST clients under an independent
subnet mask, or upgrade your network hardware.
Refer to
page
21 34
21 34
21 34
MCX-
1000
owners
manual,
page 21
10, 12, 13
11, 20
26, 27
21 34
20
MCX-
1000
owners
manual,
page 121
MCX-
1000
owners
manual,
page 121
21 34
21 34
21 34
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is
not listed below or if the instruction below does not help, set this unit to the standby mode, disconnect the
power cord, and contact the nearest authorized YAMAHA dealer or service center.
105_Musiccast_E.p65 2003.06.28, 19:0369
68


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha mcx-a10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha mcx-a10 in the language / languages: English as an attachment in your email.

The manual is 3,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info