549947
58
Zoom out
Zoom in
Previous page
1/68
Next page
58
SYMPTOM
No sound from the center speaker.
The sound field cannot be recorded.
The DVD/LD, TV or DBS source
cannot be recorded on a tape deck,
MD recorder or VCR connected to
this unit.
FM stereo reception is noisy.
There is distortion and clear
reception cannot be obtained even
with a good FM antenna.
The desired station cannot be tuned
in with the automatic tuning method.
Previously preset stations can no
longer be tuned in.
The desired station cannot be tuned
in with the automatic tuning method.
There are continuous crackling and
hissing noises.
There are buzzing and whining
noises (especially in the evening).
The remote control transmitter does
not work.
CAUSE
The input signals of the source encoded
with Dolby Digital do not have center
channel signals.
The sound output level of the center
speaker is set to minimum.
The function “CNTR” in the SET MENU
is set to the NONE position.
Incorrect sound field program selection.
It is not possible to record the sound
field on a tape deck or MD recorder
connected to the unit’s REC OUT
terminals.
The DVD/LD player, TV or DBS tuner is
connected to the unit by only the digital
terminals.
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
There is multipath interference.
The station is too weak.
This unit has been unplugged for a long
period.
The signal is weak or antenna
connections are loose.
Noise will result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
A television set is being used nearby.
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of the
this unit.
The manufacturer’s code has not been
set properly.
The proper manufacturers code for the
component to be controlled has not
been set.
The component to be controlled has not
been selected.
REMEDY
Refer to the instruction for the source
being currently played.
Raise the sound output level of the
center speaker.
Select the LARGE or SMALL position.
Select the appropriate program.
Make additional connections between
the analog terminals.
Check the antenna connections.
Try using a high-quality directional FM
antenna.
Set TUNING MODE to the manual
tuning mode.
Adjust antenna position to eliminate
multipath interference.
Use the manual tuning method.
Use a high-quality directional FM
antenna.
Repeat the presetting procedure.
Tighten the AM loop antenna
connections and rotate it for best
reception.
Use the manual tuning method.
Use an outdoor antenna and a ground
wire. This will help somewhat, but it is
difficult to eliminate all noise.
Relocate this unit away from the TV.
Change the position of the unit.
Set the code again.
Try entering another code for the same
manufacturer.
Press the component selector which
matches the component to be
controlled.
Remote control transmitter
AM FM
Amplifier
01RX-V495RDS-7 6/22/99, 12:29 PM58
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha HTR-5140RDS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha HTR-5140RDS in the language / languages: English as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info