549947
56
Zoom out
Zoom in
Previous page
1/68
Next page
56
SETUP CODES
To control your components
(MD recorder, DVD player,
TV, etc.)
1. Turn on the component to be used.
2. Press the component selector which
matches the component to be
controlled (TAPE/MD, DVD/LD, TV
etc.).
3. Press both VOLUME buttons (
) for about four seconds at the
same time so that the indicator
flashes twice.
4. Use the numeric buttons to enter the
four-digit manufacturer’s code for
the component to be used. Make
sure that the indicator flashes twice.
If the indicator does not flash, repeat
step 3 and re-enter the code.
5. Press POWER (or any other button)
on the remote control transmitter to
check if you have preset the code
correctly. If the component cannot
be controlled by the remote control
transmitter, try entering another
code for the same manufacturer.
Returning to the factory-set
codes
To return all components to the factory-
set codes, follow these steps.
1. Press a button on the component
selector other than AMP<TUNER>.
2. Press both VOLUME buttons (
) for about four seconds at the
same time so that the indicator
flashes twice.
3. Enter the code number “9990”.
4. Make sure that the indicator flashes
twice.
To return each component to the factory-
set codes, follow these steps.
1. Press the component selector which
matches the component to be
returned to the factory-set codes.
2. Press both VOLUME buttons (
) for about four seconds at the
same time so that the indicator
flashes twice.
3. Enter the code number “0000”.
4. Make sure that the indicator flashes
twice.
The following codes are preset by the
factory.
Factory-set codes
Component
Component Code
selector
TV TV 0101
CBL/DBS DBS tuner 0006
VCR VCR 0002
DVD/LD DVD player
0008 YAMAHA
CD CD player
0005 YAMAHA
TAPE/MD Tape deck
0004 YAMAHA
We recommend that you write all code
numbers you have preset on the “Quick
Reference Card”.
Presetting the remote control transmitter
Perform the presetting procedure for each component you want to control with the remote control transmitter.
Note: If your component does not respond to any of the codes listed for the manufacturer, use the original remote control
transmitter that was supplied with the component.
To use a second (and third) VCR
You can control a second (and/or third)
VCR in the CBL/DBS and DVD MENU
modes if a CBL (or DBS) or DVD player
is not being used.
If you want to control a second (and/or
third) VCR in the DVD MENU mode, you
must preset the code for an LD player in
that mode.
1. Turn on the VCR to be used.
2. Press CBL/DBS or DVD MENU on
the component selector.
3. Press both VOLUME buttons (
) for about four seconds at the
same time so that the indicator
flashes twice.
4. Use the numeric buttons to enter the
four-digit code for the second (or
third) VCR. Make sure that the
indicator flashes twice. If the
indicator does not flash, repeat step
3 and re-enter the code.
5. Press POWER (or any other button)
on the remote control transmitter to
check if you have preset the code
correctly. If the VCR cannot be
controlled by the remote control
transmitter, try entering another
code for the same manufacturer.
01RX-V495RDS-6 6/22/99, 12:29 PM56
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha HTR-5140RDS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha HTR-5140RDS in the language / languages: English as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info