667653
92
Zoom out
Zoom in
Previous page
1/116
Next page
83
E F ES D
AE01079
ENGINE
1. Remove the spark plug,
pour about one tablespoon
of SAE 10W30 or 20W40
motor oil into the spark plug
hole and reinstall the spark
plug. Recoil start the engine
by turning over several
times (with ignition off) to
coat the cylinder walls with
oil.
2. Pull the recoil starter until
you feel compression. Then
stop pulling. (This prevents
the cylinder and valves from
rusting).
3. Clean exterior of the gener-
ator and apply a rust in-
hibitor.
4. Store the generator in a dry,
well-ventilated place, with
the cover placed over it.
5. The generator must remain
in a vertical position when
stored, carried or operated.
The caster lock lever should
be in the LOCK position
when stored or operated.
AF01079
MOTEUR
1. Déposez la bougie, versez en-
viron une cuillère à soupe
dhuile SAE 10W30 ou 20W40
dans lorifice de la bougie, puis
remontez la bougie. Essayez à
plusieurs reprises de mettre le
moteur en marche à laide du
lanceur (en laissant lallumage
hors circuit). Cette précaution
permettra denduire dhuile la
paroi du cylindre.
2. Tirez sur le cordon du lanceur
jusqu’à ce que vous sentiez une
certaine compression; cessez
alors de tirer (ceci empêche le
cylindre et les soupapes de
rouiller).
3. Nettoyez lextérieur du groupe
électrogène et appliquez un
produit antirouille.
4. Remisez le groupe électrogène
dans un endroit sec et bien
aéré, en prenant soin de le cou-
vrir.
5. Le groupe électrogène doit res-
ter en position verticale lorsque
vous le remisez, le transportez
ou lutilisez. Le levier de ver-
rouillage des roulettes doit être
sur la position verrouillée
« LOCK » lorsque le généra-
teur fonctionne ou lorsquil est
remisé.
AS01079
MOTOR
1. Saque la bujía, vierta aproxima-
damente una cucharada de aceite
de motor SAE 10W30 o 20W40
en la cavidad de la bujía y vuelva
a instalar ésta. Dé varias vueltas
al arranque por retroceso (con el
encendido desconectado) con el
fin de recubrir de aceite las pare-
des del cilindro.
2. Tire del arranque por retroceso
hasta que note la compresión.
Deje entonces de tirar. (Con ello
evita que se oxiden el cilindro y
las válvulas.)
3. Limpie el exterior del generador y
aplique un inhibidor de corrosión.
4. Almacene el generador en un
lugar seco y bien ventilado y cú-
bralo con una funda.
5. El generador debe mantenerse en
posición vertical mientras esté al-
macenado, se transporte o se uti-
lice. La palanca de bloqueo de las
roldanas debe estar en la posición
de “LOCK” (BLOQUEO) durante
el almacenamiento o manejo.
AG01079
MOTOR
1. Zündkerze herausschrauben,
ca.1 Eßlöffel Motoröl SAE
10W30, 10W40, oder 20W40 in
die Zündkerzenöffnung gießen
und die Kerze wieder einschrau-
ben. Motor mit dem Hand-
Seilzugstarter einige Male (bei
abgestellter Zündung) durchdre-
hen, um die Zylinderwand mit Öl
zu benetzen.
2. Hand-Seilzugstarter ziehen, bis
ein Gegendruck (Kompression)
zu spüren ist. Handstartseil lang-
sam zurück gleiten lassen.
(Durch diese Maßnahme sind
Einlaß- und Auslaßventil ge-
schlossen. Dadurch wird
Rostbildung im Zylinder und an
den Ventilen vermieden).
3. Außenseiten des Stromerzeugers
säubern und mit einem
Rostschutzmittel einnebeln.
4. Stromerzeuger abgedeckt an
einem trockenen, gut belüfteten
Platz lagern.
5. Der Stromerzeuger muß sowohl
bei der Lagerung als auch beim
Transport und im Betrieb immer
waagrecht stehen. Der
Laufrollen-Arretierungshebel soll-
te bei der Lagerung und im
Betrieb in der Arretierungs-
stellung LOCK stehen.
712-028
712-029b
7CH-9-1L-b 6/21/04 10:29 AM Page 38
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha EF3000iSEB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha EF3000iSEB in the language / languages: English, German, Dutch, French, Italian, Spanish, Norwegian as an attachment in your email.

The manual is 7,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha EF3000iSEB

Yamaha EF3000iSEB User Manual - English - 47 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info