464180
124
Zoom out
Zoom in
Previous page
1/150
Next page
Troubleshooting
124 En
Remote control
HDMI
Network and USB
“CHECK SP WIRES”
appears in the front panel
display.
Speaker cables are short-circuited. Make sure all speaker cables are connected correctly.
23
There is noise interference
from digital or radio
frequency equipment.
This unit is too close to the digital or high-
frequency equipment.
Move this unit further away from such equipment.
The picture is disturbed. The video source uses scrambled or encoded
signals to prevent dubbing.
This unit suddenly enters
the standby mode.
The internal temperature becomes too high and the
overheat protection circuitry has been activated.
Wait about 1 hour for this unit to cool down and then turn it
back on.
Problem Cause Remedy See page
Problem Cause Remedy See page
The remote control does
not work or function
properly.
Wrong distance or angle. The remote control will function within a maximum range of 6
m (20 ft) and no more than 30 degrees off-axis from the front
panel.
12
Direct sunlight or lighting (from an inverter type of
fluorescent lamp, etc.) is striking the remote
control sensor of this unit.
Reposition this unit.
The batteries are weak. Replace all batteries.
11
The batteries do not last long and get quickly
exhausted.
Using alkaline batteries is strongly recommended.
Set the backlight mode to “OFF”.
104
The operation mode selector is set incorrectly. Set the operation mode selector correctly.
When operating this unit, set it to the
F
AMP position.When
operating the component selected by the input selector button,
set it to the
F
SOURCE position. When operating the TV, set it
to the
F
TV position.
The remote control code was not correctly set. Set the remote control code correctly using
“List of remote control codes” at the end of this manual.
104
Try setting another code of the same manufacturer using “List
of remote control codes” at the end of this manual.
104
The remote control ID of the remote control and
this unit do not match.
Match the remote control ID of this unit and the remote control.
104
The remote control does
not work or function
properly.
Even if the remote control code is correctly set,
there are some models that do not respond to the
remote control.
Program the necessary functions independently into the
programmable buttons using the Learn feature.
105
The remote control does
not learn new functions.
The batteries of this remote control and/or the
other remote control are too weak.
Replace the batteries.
11
The distance between the two remote controls is
too much or too little.
Place the remote controls at the proper distance.
105
The signal coding or modulation of the other
remote control is not compatible with this remote
control.
Learning is not possible.
Memory capacity is full. Delete other unnecessary functions to make room for the new
functions.
109
Problem Cause Remedy See page
No picture or sound
The number of the connected HDMI components
is over the limit.
Reduce the number of the connected HDMI components.
HDCP authentication failed. Check that the connected HDMI components support the HDCP
copy protection standards.
Problem Cause Remedy See page
The PC server/MCX-2000/
Internet Radio does not
function properly.
The IP address is not set properly. Set the DHCP server function of the router to ON.
Alternately, perform manual configuration according to the
current operating environment.
92
The network cable is not connected. Connect it properly.
37
124


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha DSP-Z11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha DSP-Z11 in the language / languages: English as an attachment in your email.

The manual is 4,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha DSP-Z11

Yamaha DSP-Z11 User Manual - German - 150 pages

Yamaha DSP-Z11 User Manual - Dutch - 150 pages

Yamaha DSP-Z11 User Manual - French - 150 pages

Yamaha DSP-Z11 User Manual - Italian - 150 pages

Yamaha DSP-Z11 User Manual - Swedish - 150 pages

Yamaha DSP-Z11 User Manual - Spanish - 150 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info