464180
122
Zoom out
Zoom in
Previous page
1/150
Next page
Troubleshooting
122 En
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction
below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.
General
Troubleshooting
Problem Cause Remedy See page
This unit fails to turn on or
enters the standby mode
soon after the power is
turned on.
The power cable is not connected or the plug is not
completely inserted.
Connect the power cable firmly.
The speaker impedance setting is incorrect. Set the speaker impedance to match your speakers.
39
The protection circuitry has been activated. Make sure that all speaker wire connections on this unit and on
all speakers are secure and that the wire for each connection
does not touch anything other than its respective connection.
23
This unit has been exposed to a strong external
electric shock (such as lightning or strong static
electricity).
Set this unit to the standby mode, disconnect the power cable,
plug it back in after 30 seconds and then use it normally.
No sound. Incorrect input or output cable connections. Connect the cables properly. If the problem persists, the cables
may be defective.
30-38
Audio input jack select is set to “HDMI”, “Coax/
Opt” or “Analog”.
Set the audio input jack select to “Auto”.
52
Audio input jack select is set to “Analog” while
the input source component outputs digital audio
signals.
Set the audio input jack select to “Auto” or
“Coax/Opt”.
52
No appropriate input source has been selected.
Select an appropriate input source with the
D
INPUT selector
on the front panel (or the input selector buttons (3) on the
remote control).
50
Speaker connections are not secure. Secure the connections.
23
The volume is turned down. Turn up the volume.
The front speakers to be used have not been
selected properly.
Select the front speakers by pressing GSPEAKER A or
GSPEAKER B on the front panel.
51
The sound is muted.
Press
L
MUTE or
J
VOLUME +/– on the remote control to
resume audio output and then adjust the volume.
52
Signals this unit cannot reproduce are being input
from a source component, such as a CD-ROM.
Play a source whose signals can be reproduced by this unit.
The HDMI components connected to this unit do
not support the HDCP copy protection standards.
Connect HDMI components that support the HDCP copy
protection standards.
28
“Support Audio” is set to “Other” and HDMI
audio signals are not being played back on this
unit.
Set “Support Audio” in “Option” to “DSP-Z11”.
94
No picture. The output and input for the picture are connected
to different types of video jacks.
Set “Conversion” to “On” or connect your source components
in the same way as you connect your video monitor to this unit.
89
This unit outputs the video signals are not
supported in the video monitor connected to the
HDMI OUT jack.
Set the “INITIALIZE” to “VIDEO” to reset the video
parameters.
120
Set “MONITOR CHECK” to “YES”.
120
Input selector setting of the video monitor is
incorrect.
Set the input source selector setting of the video monitor
appropriately.
Pure Direct mode is active. Turn off the Pure Direct mode.
Set “Pure Direct” in “Sound” to “Video On”.
89
Non-standard video signals are input.
The HDMI OUT jack that the video monitor is
connected is not selected.
Press CHDMI OUT on the remote control repeatedly.
51
Short message displays in
the main zone do not
appear in the video
monitor.
“Short Message” is set to “Off”. Set “Short Message” to “On”.
90
“Conversion” is set to “Off”. Set “Conversion” to “On”.
89
The signals input at the HDMI input jacks are
being output at the HDMI OUT jack.
The sound suddenly goes
off.
The protection circuitry has been activated because
of a short circuit, etc.
Check that the speaker impedance setting is correct.
39, 119
Check that the speaker wires are not touching each other and
then turn this unit back on.
The sleep timer has turned off this unit. Turn on this unit, and play the source again.
The sound is muted.
Press
L
MUTE or
J
VOLUME +/– on the remote control to
resume audio output.
52
122


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yamaha DSP-Z11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yamaha DSP-Z11 in the language / languages: English as an attachment in your email.

The manual is 4,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Yamaha DSP-Z11

Yamaha DSP-Z11 User Manual - German - 150 pages

Yamaha DSP-Z11 User Manual - Dutch - 150 pages

Yamaha DSP-Z11 User Manual - French - 150 pages

Yamaha DSP-Z11 User Manual - Italian - 150 pages

Yamaha DSP-Z11 User Manual - Swedish - 150 pages

Yamaha DSP-Z11 User Manual - Spanish - 150 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info