655217
9
Zoom out
Zoom in
Previous page
1/20
Next page
9
Mounting the Door/Window Contact
Note:The Door/Window Contact and magnet can be
changed round as long as there is no more than a 10mm
gap.
1. Find a location on the door/window where you would
like the device to be mounted. The sensor should be
on the frame while the magnet should be on the door/
window. Once mounted make sure the tamper switch
spring is fully depressed.
Mounting using adhesive pads
Clean the mounting surface with a suitable degreaser
agent. Please note that some surfaces may be unsuitable
for this mounting method. Please use screw mounting in
these cases.
Mounting using screws & wall plugs
Loosen the bottom screw and open the door/window
contact. Knock out the holes on the base as shown. Drill
holes into the mounting surface using the holes in the
knockouts on the base as a template. Fit wall plugs (if
required) and secure with the screws provided.
Mounting the External Siren
Ensure the tamper spring is fully compressed when
the siren is mounted. If there is a gap, pack with a
suitable spacing material.
1. Using the large screws and wall plugs provided, screw
the Siren onto the wall through the 4 mounting holes on
the Siren base.
2. Fix the Siren cover with the securing screw.
Mounting the Panic Button
1. Break through the knockouts (where the plastic
is thinner).
2. Using the holes as a template, drill holes in the surface
and insert wall plugs if xing into plaster or brick. Screw
the rear case to the wall. Replace the cover and tighten
the screw.
Mounting the Smoke Detector
1. The base has two mounting slots. Using the slots as
a template, drill holes and insert the wall plugs if xing
to plaster. Screw the rear case to the ceiling using the
screws provided.
2. Replace the main unit onto the bracket.
Display extreme caution when using ladders or steps,
please follow manufacturer’s instructions.
Be careful when using hand and power tools and follow
the manufacturer’s guidelines when using them. Take care
that the correct tools are used. Wear goggles or protective
clothing where required. The Siren is extremely loud, please
ensure to retreat to a safe distance before testing.
The gap between the magnet and sensor
should be no more than 10mm when closed
(maybe shorter depending upon the actual
environment).Simply test to see whether the
magnet is in range of the sensor: hold the
magnet and sensor in place and then pull
them apart. If the sensor LED lights up it
implies the two items are within range.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yale SR310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yale SR310 in the language / languages: English as an attachment in your email.

The manual is 2,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info