478483
70
Zoom out
Zoom in
Previous page
1/88
Next page
VX-170 OPERATING MANUAL68
of a wide variety of transceiver parameters, some of which have not been detailed previ-
ously. Use the following procedure to activate the Set Mode:
1. Press the
[
F
]
key, then press the
[
0
(
SET
)]
key to enter the Set mode.
2. Rotate the DIAL knob to select the Set Mode Item to be adjusted.
3. Press the
[
F
]
key momentarily to enable adjustment of the Set
Mode Item.
4. Rotate the DIAL knob to adjust or select the parameter to be
changed on the Set Mode Item selected in above step.
5. After completing your selection and adjustment, press the PTT
switch momentarily to save the new setting and exit to normal
operation.
1) Some Set Mode Items (like Set Mode Item 46: TN FRQ) require that the [F] key be
pressed after setting of the parameter, and before exiting to normal operation.
2) Two Set Mode Item numbers (in the factory default, Set Mode Item 25:
LAMP, and 32: RESUME) will blink while selecting the Set Mode Item; this
indicates that this Set Mode Item has been assigned to the [7(P1)] or [8(P2)]
key of the keypad.
Set Mode Item 1
[
APO
]
Function: Setting of the Automatic Power-Off feature.
Available Values: OFF/0.5H - 12.0 H in 0.5 hour multiples
SET
(
MENU
)
M
ODE
SET MODE ITEM
1
[
APO
]
2
[
AR BEP
]
3
[
AR INT
]
4
[
ARS
]
5
[
BCLO
]
6
[
BEEP
]
7
[
BELL
]
8
[
BSY.LED
]
9
[
CLK.SFT
]
10
[
CWID
]
11
[
CW WRT
]
12
[
DC VLT
]
13
[
DCS.COD
]
14
[
DCS.N/R
]
15
[
DT DLY
]
16
[
DT SPD
]
17
[
DT WRT
]
18
[
ECS.CDR
]
19
[
ECS.CDT
]
20
[
EDG.BEP
]
FUNCTION
Setting of the Automatic Power-Off feature.
Selects the Beep option during ARTS operation.
Selects the Polling Interval during ARTS operation.
Enables/Disables the Automatic Repeater Shift function.
Enables/Disables the Busy Channel Lock-Out feature.
Enables/Disables the beeper.
Selects the number of CTCSS/DCS Bell ringer repetitions.
Enables/Disables the BUSY LED while the Squelch is open.
Shifting of the CPU clock frequency.
Enables/disables the CW identifier during ARTS operation.
Programs and activates the CW Identifier.
Indicates the DC Supply Voltage.
Setting of the DCS code.
Enables/Disables “Inverted” DCS code decoding.
Setting of the DTMF Autodialer Delay Time.
Setting of the DTMF Autodialer Sending Speed.
Programming of the DTMF Autodialer.
Setting the Receiver Pager Code for the Enhanced CTCSS
Paging & Code Squelch.
Setting the Transmitting Pager Code for the Enhanced
CTCSS Paging & Code Squelch.
Enables/Disables the Band-edge beeper while selecting the
frequency via the DIAL knob.
AVAILABLE VALUES
(
D
EFAULT: BOLD ITALIC
)
OFF / 0.5H - 12.0 H
INRANG / ALWAYS / OFF
25 SEC / 15 SEC
ARS. ON / ARS.OFF
BCL. ON / BCL.OFF
KEY+SC / KEY / OFF
OFF / 1T / 3T /
5T / 8T / CONT
LED. ON / LED.OFF
SFT.OFF / SFT. ON
TX OFF / TX ON
---
---
104 DCS codes (023)
T/RX N, RX R,
TX R, T/RX R
50MS / 100MS / 250MS /
450MS / 750MS / 1000MS
50MS / 100MS
---
(R05 47)
(T05 47)
BEP.OFF / BEP. ON
70


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu VX-170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu VX-170 in the language / languages: English as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info