674768
110
Zoom out
Zoom in
Previous page
1/173
Next page
110
Communicating with a Specific Remote Station
Using the Tone Squelch Function
Tips
The squelch type can be set for each frequency band on both A-band (Main) and B-band (Sub).
The CTCSS and DCS squelch settings are also active during scanning. If scanning is performed with
the CTCSS and DCS squelch function activated, scanning stops only when a signal containing the
specified CTCSS tone or DCS code is received.
Pressing the Monitor switch allows signals that do not contain a tone or DCS code, and signals with
different tones or DCS codes to all be heard.
Pressing and holding the
key for over one second to change the Set mode option allows you
to use this function more conveniently.
[SIGNALING][3 DCS INVERSION]: Allows you to receiving the DCS code of the inverted phase.
[SIGNALING] [10 SQL EXPANSION]: Allows specifying squelch types for transmit and receive
respectively.
Display Operation
OFF Deactivates transmit/ receive tone squelch function, etc.
TONE Activates CTCSS transmit tones ([TN] appears).
TONE SQL Activates the tone squelch receive function ([TSQ] appears).
DCS Activates the digital code squelch ([DCS] appears).
REV TONE
Activates the reverse tone ([RTN] appears).
Use to monitor communications based on the squelch control system in which
a tone signal is contained when communication is not performed and the tone
signal disappears when communication starts.
PR FREQ
Activates the no-communication squelch function for radios ([PR] appears).
You can specify no-communication signal tone frequencies within the range from
300 Hz to 3000 Hz in steps of 100 Hz.
PAGER (
see page
116)
Activates a new pager function ([PAG] appears).
When communicating via transceivers with your friends, specify personal codes
(each code is composed of two tones) so that you can call only specific stations.
D CD* Sends a DCS code only for transmission ([DC] appears).
TONE-DCS*
Sends a tone signal when transmitting, and waits for a DCS code when receiving
([T-D] appears).
D CD-TONE SQL*
Sends a DCS code when transmitting, and waits for a tone signal when receiving
([D-T] appears).
*: Press and hold the
key for over one second, then set [SIGNALING][10 SQL EXPANSION] to
ON. The setting options for D CD, TONE-DCS and D CD TONE SQL are added to the [SIGNALING] [11
SQL TYPE] in Set mode. This allows specifying the squelch types for transmit and receive respectively.
Setting the Tone Frequency
The tone frequency can be selected from 50 frequencies (from 67.0 Hz to 254.1 Hz).
1 Press and hold the key for over one second.
The transceiver enters Set mode.
2 Touch [SIGNALING].
3 Rotate the dial, then touch [12 TONE SQL FREQ].
110


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT2DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT2DR in the language / languages: English as an attachment in your email.

The manual is 40,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info