674767
60
Zoom out
Zoom in
Previous page
1/156
Next page
60
Scanning Function
Using the Scanning Function
Tips Turn O clockwise.: Scanning is performed toward higher memory channel numbers.
Turn O counterclockwise: Scanning is performed toward lower memory channel numbers.
When a signal is received during scanning, scanning stops for 5 seconds and this frequency
is received.
When scanning is suspended, the decimal point blinks and the LCD stays lit.
After receiving the frequency for 5 seconds, scanning resumes.
To stop scanning, press p.
Tips
Even during scanning, you can adjust the squelch in the following procedure:
Press F  Press T.  Turn O to adjust the squelch.
During scanning, you can finish the squelch adjustment in the following procedure:
Press F  Press T.
When a memory channel is recalled, the regular memory channels (memory channel numbers
1-900) are scanned.
When a memory bank is recalled, only the memory channels in the memory bank are scanned.
For the operation to perform when scanning stops, see [Selecting a Reception Method When
Scanning Stops] on page 59.
Press and hold M over 1 second to select the Set mode option, and then select the following
setting items for more convenient use:
[8 CONFIG]  [3 BEEP]  [EDGE]: Emits a beep when the frequency band edge is reached.
[8 CONFIG]  [3 BEEP]  [SELECT]: Prevents a beep from being emitted when scanning stops.
[5 SCAN]  [2 SCAN LAMP]: Prevents the LCD from being lit when scanning stops.
[5 SCAN WIDTH]  [5 SCAN]: Range for scanning can be selected.
Specifying a Skip/Selected Memory Channel
You can specify two types of memory channels, a skip memory channel and a selected
memory channel, for effective memory channel scanning.
Skip memory channel: You can specify a memory channel that need not be scanned
during memory channel scanning.
Selected memory channel: You can specify selected memory channels so that only
the specific memory channels are scanned during memory
scanning.
1 Switch to the Memory mode, and then recall the memory
channel you want to specify as a skip memory channel or a
selected memory channel.
2 Press and hold M over 1 second.
Enters the Set mode.
3 Turn O to select [3 MEMORY].
4 Press H.
5 Turn O to select [5 MEMORY SKIP].
6 Press H.
7 Turn O to select [OFF], [SKIP], or [SELECT].
8 Press p to save the setting and exit from the Set mode.
FT1DR_DE_Eng.indb 60FT1DR_DE_Eng.indb 60 13/06/28 15:1613/06/28 15:16
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT1DR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT1DR in the language / languages: English as an attachment in your email.

The manual is 6,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info