674754
141
Zoom out
Zoom in
Previous page
1/156
Next page
Page 139FTDX9000D OPERATION MANUAL
MENU MODE
MODE-SSB GROUP
069. SSB MIC SELECT
Function: Selects the microphone to be used on the
SSB mode.
Available Values: FRONT/REAR/DATA/PC
Default Setting: FRONT
FRONT: Selects the microphone connected to the
front panel’s MIC jack while using the SSB
modes.
REAR: Selects the microphone connected to the
rear panel’s MIC jack while using the SSB
modes.
DATA: Selects the microphone connected to pin 1
of the PACKET Jack while using the SSB
modes.
PC: Selects the microphone connected to the
rear panel’s AUDIO IN 3.5-mm jack while
using the SSB modes.
070. SSB-TX-BPF
Function: Selects the audio passband of the En-
hanced DSP modulator on the SSB mode.
Available Values: 50-3000(Hz)/100-2900(Hz)/
200-2800(Hz)/300-2700(Hz)/400-2600(Hz)/3000WB
Default Setting: 300-2700 Hz
071. LSB RX-CARRIER
Function: Adjusts the receiver carrier point for LSB
mode.
Available Values: –200 Hz ~ +200 Hz (10 Hz steps)
Default Setting: 0 Hz
072. LSB TX-CARRIER
Function: Adjusts the transmitter carrier point for LSB
mode.
Available Values: –200 Hz ~ +200 Hz (10 Hz steps)
Default Setting: 0 Hz
073. USB RX-CARRIER
Function: Adjusts the receiver carrier point for USB
mode.
Available Values: –200 Hz ~ +200 Hz (10 Hz steps)
Default Setting: 0 Hz
074. USB TX-CARRIER
Function: Adjusts the transmitter carrier point for USB
mode.
Available Values: –200 Hz ~ +200 Hz (10 Hz steps)
Default Setting: 0 Hz
RX AUDIO GROUP
075. AGC-SLOPE
Function: Selects the gain curve of the AGC ampli-
fier.
Available Values: NORMAL/SLOPE
Default Setting: NORMAL
NORMAL: The AGC output level will follow a linear
response to the antenna input level, while
AGC is activated.
SLOPE: The AGC output level will increase at 1/10
the rate of the antenna input level, while
AGC is activated.
076. HEADPHONE MIX
Function: Selects one of three audio mixing modes
when using headphones during Dual Receive opera-
tion.
Available Values: SEPARATE/COMBINE-1/COM-
BINE-2
Default Setting: SEPARATE
SEPARATE: Audio from the main (VFO-A) receiver
is heard only in the left ear, and sub
(VFO-B) receiver audio solely in the
right ear.
COMBINE-1: Audio from both main (VFO-A) and sub
(VFO-B) receivers can be heard in both
ears, but sub (VFO-B) audio is attenu-
ated in the left ear and main (VFO-A)
audio is attenuated in the right ear.
COMBINE-2: Audio from both main (VFO-A) and sub
(VFO-B) receivers is combined and
heard equally in both ears.
077. SPEAKER OUT
Function: Selects audio mixing modes for the “sub”
(secondary) speaker during Dual Receive operation.
Available Values: SEPARATE/COMBINE
Default Setting: COMBINE
SEPARATE: Audio from the main (VFO-A) receiver
is fed to the main speaker, and sub
(VFO-B) receiver audio is fed to the
“sub” speaker.
COMBINE: Audio from both main (VFO-A) and sub
(VFO-B) receivers is combined and split
equally between the main and sub
speakers.
NORMAL
Input Signal
A
u
d
i
o
O
u
t
p
u
t
SLOPE
141


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-DX9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-DX9000 in the language / languages: English as an attachment in your email.

The manual is 25,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info