674754
45
Zoom out
Zoom in
Previous page
1/156
Next page
Page 43FT DX 9000D OPERATION MANUAL
B
ASIC
O
PERATION
: R
ECEIVING
ON
A
MATEUR
B
ANDS
1. Plug the AC cable back in, set the rear-panel
Power switch to “
I
.”
2. Press and hold in the front-panel Power
switch for two seconds to turn the trans-
ceiver on.
3. After about 50 seconds, all circuits will
be initialized. The transceiver will start
up on 7.000.00 MHz LSB, and normal operation may
resume.
Note
To turn power off, press and hold in the front panel
POWER switch for two seconds.
Quick Note
The opening screen on the TFT will be gray, and some
text notes advising status during the boot-up sequence
may appear. When the radio is turned on for the first
time, it takes about 50 seconds (from turning the ra-
dio on to completing the self-check) until the radio
becomes ready to use; however, from the next time
you turn it on, it will take around 10 seconds until the
transceiver is ready for full operation.
4. Rotate the AF GAIN
knob (# ) to set a comfort-
able audio level on incom-
ing signals or noise. Clock-
wise rotation of the AF
GAIN knob increases the
volume level.
Note
When using headphones, start by rotating the AF
GAIN control counter-clockwise, then bring the vol-
ume level up after you put the headphones on. This
will minimize the chance of damage to your hearing
caused by an unexpectedly-high audio level.
5. Press the MAIN RX switch (# ) to engage the
Main (VFO-A) receiver, the imbedded LED will glow
Green.
BAND key
POWER swtch
AF GAIN knob
Main (VFO-A)
RX switch
Main (VFO-A)
Advice
If you press the MAIN RX key (# ) when the
imbedded LED is already glowing Green, the LED
will now blink on and off; this indicates that the Main
(VFO-A) receiver is temporarily muted. Just press the
MAIN RX key once more to restore Main (VFO-
A) receiver operation.
Press the SUB RX switch (# ) to engage Dual
Reception (using Sub the (VFO-B) receiver in addi-
tion to the Main (VFO-A) receiver). When you press
the SUB RX key, its imbedded LED will glow green;
pressing this key once more will turn off the Sub (VFO-
B) receiver, and the impeded LED will glow dark. Use
the Sub Receivers AF GAIN knob (# ) to adjust
the Sub (VFO-B) receiver volume level.
6. Press the A switch (# ) to enable
the capability to change the operation
for the Main (VFO-A) band the im-
bedded LED will glow Red.
7. Surrounding the TFT are the band
selection keys; press the BAND
key corresponding to the Amateur
band on which you wish to begin op-
eration.
Advice
H One-touch selection of each
Amateur band between 1.8 and
50 MHz is provided.
H If you press the BAND/MHz
key (# ) momentarily, the CLAR/VFO-B
knob (# ) may be used as a band selection knob.
If the CLAR/VFO-B
knob is pressed and held
in for two seconds, rota-
tion of the BAND/
MHz key allows fre-
quency navigation in 1
MHz steps.
H When the BAND/MHz key’s imbedded LED
is illuminated, the CLAR/VFO-B knob controls
the functions associated with the BAND/MHz
key.
CLAR/VFO-B knob
AF GAIN knob
Sub (VFO-B)
RX swtch
Sub (VFO-B)
BAND/MHz switch
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-DX9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-DX9000 in the language / languages: English as an attachment in your email.

The manual is 25,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info