674754
38
Zoom out
Zoom in
Previous page
1/156
Next page
Page 36 FT DX 9000D OPERATION MANUAL
ANT
Connect your main antenna(s) here, using a type-M
(PL-259) plug and coaxial feedline for each. These
antenna ports are always used for transmission, and
also are used for reception unless a separate receive
antenna is also used for the main receiver. The inter-
nal antenna tuner affects only the antenna(s) connected
here, and only during transmission. These connectors
utilize TeflonR insulation for extreme durability and
to ensure stable impedance over the entire frequency
range.
RX OUT
These BNC jacks provide output of the receiver sig-
nal lines from the Antenna jacks which are connected
to the Main (VFO-A) and sub (VFO-B) front ends.
Main Power Switch
This is main power On (
I
)/Off (
O
) switch of the FT
DX 9000. Always turn this switch on before turning on
the front panel’s POWER button.
If this switch is not turned On, the front panel Power
switch will not function.
Turning this Main Power switch On supplies voltage
to the OCXO (Crystal Oven), ensuring that frequency
stability is always maintained even when the trans-
ceiver is turned off via the front panel's Power switch.
AC IN
Connect the supplied 3-wire AC line cord to this
socket. AC voltages of 100-240 V may be accommo-
dated by the FT DX 9000D without any sort of modifi-
cation (universal voltage input).
CIRCUIT BREAKER Switch
This circuit breaker shuts off in the event of danger-
ously high current consumption by the transceiver.
Advice
If the Circuit Breaker interrupts power, by all means
try to determine the cause of the over-current condi-
tion before re-applying power. To restore the Circuit
Breaker after verifying that all is normal, push this
switch in until you hear a “click.”
MIC
This 8-pin jack accepts input from a microphone uti-
lizing a traditional YAESU HF-transceiver pinout.
REMOTE
By plugging in the supplied FH-2 Remote Control Key-
pad to this gold-plated jack, direct access to the FT DX
9000D CPU is provided for control functions such as
contest memory keying, plus frequency and function con-
trol. This jack may also be also used for remote control
of the VL-1000 Linear Amplifier, if used.
RX ANT
This type-M jack is for a separate receive-only an-
tenna. An antenna connected here can be used, by both
the main (VFO-A) and sub (VFO-B) receivers, when
the RX ANT button on the front panel is pressed.
If you want to use some special kind of external
bandpass filter or preamplifier, you may connect it
between the RX OUT and RX ANT jacks, as shown
in the illustration.
REAR PANEL
A
NTENNA SWITCH
(
VFO-A
)
ANT “1”
ANT “3”
ANT “2”
ANT “4”
RX ANT
RX OUT
(
MAIN
)
RX OUT
(
SUB
)
ANTENNA SWITCH
(
VFO-B
)
RX ANTENNA SWITCH
(
VFO-B
)
RX ANTENNA SWITCH
(
VFO-A
)
TX/RX RELAY
Transmitter Section
Main
(
VFO-A
)
Receiver
Sub
(
VFO-B
)
Receiver
BPF
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-DX9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-DX9000 in the language / languages: English as an attachment in your email.

The manual is 25,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info