674754
36
Zoom out
Zoom in
Previous page
1/156
Next page
Page 34 FT DX 9000D OPERATION MANUAL
Clarifier Operation
When the CLAR switch (# above) is pushed, this knob may be used
to program an offset of up to ± 9.99 kHz from the Main (VFO-A) fre-
quency. This offset is only applied, however, to the receive or transmit fre-
quency if the FAST/RX key (# ) and/or BAND/MHz / TX key
(# ), respectively, have been pushed.
To apply the programmed frequency offset to the Receive frequency, press
the FAST/RX key (# ) momentarily. To return to the Main-VFO-A
frequency, without the offset, press the FAST/RX key once more.
To apply the programmed frequency offset to the Transmit frequency,
press the BAND/MHz / TX key (# ) momentarily. To return the
transmitter to the Main-VFO-A frequency, without the offset, press
the BAND/MHz / TX key once more.
To reset the Clarifier frequency to “0” offset, press the B-MODE/
CLEAR switch (# ).
BAND/MHz Up/Down Control
When the BAND/MHz key (# ) is pressed momentarily, the
Red LED imbedded in the switch will light up, and you may then
use this knob for selecting the desired Amateur band. If you have
engaged the “My Bands” feature via Menu #135, this knob will
select from among just the Amateur bands that you have included in
the “My Bands” list.
If you press and hold in the BAND/MHz key (# ) for 2 sec-
onds, the imbedded LED will glow Orange, and this knob may now
be used for rapid tuning in 1 MHz frequency steps.
Memory Channel/Memory Group Control
Pressing the MCH/GRP key (# ) momentarily will enable the
use of this knob for selection of the desired Memory Channel.
Pressing and holding in the MCH/GRP key for two seconds will
enable the use of this knob for selecting the desired Memory Group.
Functions Associated with Sub (VFO-B) Operation
When the A/B switch (# ) is pressed, the Orange lamp to the right of the CLAR/VFO-B knob will light up, and this knob will now be
exercising control functions associated with the Sub (VFO-B) frequency control register. If the Orange lamp is not illuminated, please press the
A/B switch (# ). Rotation of the knob will now control the Sub (VFO-B) frequency.
Sub (VFO-B) FAST Tuning
When the FAST/RX switch (# ) is pressed, the imbedded LED
will light up, and tuning of the Sub (VFO-B) frequency will in-
crease by a factor of 10. Press the FAST/RX button once more to
return to the normal tuning rate.
Sub (VFO-B) BAND/MHz Up/Down Control
If you press the BAND/MHz / TX switch momentarily, the im-
bedded LED will light up, and this knob may now be used for selec-
tion of the desired Amateur band. Pressing the BABD/MHz / TX
switch once again will cancel Up/Down Band selection, and the
LED will turn off.
If you press and hold in the BAND/MHz / TX switch for 2 sec-
onds, the imbedded LED will light up, and this knob may now be
used for Up/Down tuning of the Sub (VFO-B) frequency in 1 MHz
steps. Press the BAND/MHz / TX switch momentarily to cancel
Up/Down tuning; the imbedded LED will turn off.
Sub (VFO-B) Mode Selection
When the B-MODE/CLEAR switch is pressed, the imbedded LED
will light up, and this knob may now be used for selection of the
operating mode for Sub (VFO-B) band operation. Pressing the B-
MODE/CLEAR key once more will cancel mode selection, and
the imbedded LED will turn off.
Note
Mode selection may also be accomplished by pressing the A/B key
(# ), then pressing the appropriate Mode switch (# ) to the left
of the Main tuning Dial.
FRONT PANEL CONTROLS
CLAR/VFO-B Knob
Depending on the status of the A/B switch (# , described later) the CLAR/VFO-B is used for functions associated
with the Main (VFO-A) or Sub (VFO-B) frequency control registers.
Advice
Functions Associated with Main (VFO-A) Control
In the case of Main (VFO-A) control, this knob is used for Clarifier tuning, as well as Up/Down selection of the Amateur band, Memory
Channels, 1 MHz tuning steps, or Memory Groups. For Main (VFO-A) control, be sure that the Orange lamp beside this control is not illumi-
nated. If the Orange lamp is turned on, press the A/B switch (# ) to turn it off.
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-DX9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-DX9000 in the language / languages: English as an attachment in your email.

The manual is 25,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info