674754
30
Zoom out
Zoom in
Previous page
1/156
Next page
Page 28 FT DX 9000D OPERATION MANUAL
A
B Switch
Pressing this button momentarily exchanges the con-
tents of the main band (VFO-A) (or a recalled memory
channel) and the sub band (VFO-B).
V/M Switch
This button toggles main band (VFO-A) receiver op-
eration between the memory system and the VFO.
Either “VFO,” “MEM,” or “M TUNE” will be dis-
played to the left of the main frequency display field
to indicate the current selection. If you have tuned off
of a Memory channel frequency (M TUNE), pressing
this button returns the display to the original memory
contents (MEM), and pressing it once more returns
operation to the Main VFO.
MA Switch
Pressing this button momentarily displays the contents
of the currently-selected memory channel for three sec-
onds.
Holding this button in for 2 seconds copies the data
from the currently-selected memory to the Main VFO
(VFO-A), as two beeps sound. Previous data in the
Main VFO will be overwritten.
A M Switch
Pressing and holding in this key for 1/2 second (until
the double beep) copies the current operating data from
the main band (VFO-A) into the currently selected
memory channel, overwriting any previous data stored
there.
Also, pressing and holding in this button after recall-
ing a memory, without first retuning, causes the
memory channel to be “masked,” and repeating the
process restores the masked memory.
A-BUSY Indicator
This LED glows green whenever the Main band (VFO-
A) receiver squelch is open. If this indicator is not
illuminated, and reception seems to have been “lost”
on the Main receiver for no apparent reason, check
the position of the SQL control (# , described
previously) and rotate it fully counter-clockwise to re-
store reception.
TX Indicator
This indicator glows Red during transmission.
If you attempt to transmit while operating outside of
an Amateur band, this indicator will blink Red, indi-
cating an “out of band” condition.
B-BUSY Indicator
This LED glows green whenever the Sub band (VFO-
B) receiver squelch is open. If this indicator is not
illuminated, and reception seems to have been “lost”
on the Sub receiver for no apparent reason, check the
position of the SUB (VFO-B) SQL control (# ,
described later) and rotate it fully counter-clockwise
to restore reception.
Tuning Offset Indicator
This is a tuning scale that, as configured from the fac-
tory, provides a visual CW tuning indication of the
incoming signal’s offset from your transceiver's CW
carrier frequency, as programmed by the position of
the PITCH control (# , described previously).
SPLIT Indicator
This indicator glows Red when the “Split” mode is
engaged (with the Main and Sub bands operating on
different frequencies).
FRONT PANEL CONTROLS
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-DX9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-DX9000 in the language / languages: English as an attachment in your email.

The manual is 25,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info