674754
28
Zoom out
Zoom in
Previous page
1/156
Next page
Page 26 FT DX 9000D OPERATION MANUAL
MODE Switches
A, B Button
Pressing the A or B switch will illuminate the
respective indicator imbedded within the switch, al-
lowing adjustment of the operating mode on the Main
(VFO-A) or Sub (VFO-B) band. Pressing the A
switch causes the indicator to glow Red, signifying
Main (VFO-A) band is being adjusted. Similarly,
pressing the B switch will cause its indicator to glow
Orange, signifying Sub (VFO-B) Band adjustment.
Advice
When changing bands, be sure to press the A or
B switch first, then press the appropriate Band se-
lector switch, so as to change operating frequencies
on the proper (Main or Sub) band.
LSB, USB, CW, AM, FM, RTTY, PKT Button
Pressing the LSB , USB , CW , AM , FM ,
RTTY , or PKT button will select the operating
mode. Pressing the CW , AM , RTTY , or
PKT button multiple times will switch between the
alternate operating features that can be used on these
modes (covered later). Also, when you press and hold
in the PKT button for one second, the user-pro-
grammed custom function setting mode will be acti-
vated.
QMB (Quick Memory Bank) Switch
STO (Store) Button
Pressing this button copies operating information (fre-
quency, mode, bandwidth, and also repeater direction/
shift frequency and CTCSS functions on the FM mode)
into consecutive QMB Memories.
RCL (Recall) Button
Pressing this button recalls one of up to five Quick
Memory Bank memories for operation.
RX Indicator/Switch
This switch, when pressed, engages the Main (VFO-
A) band receiver; the indicator will glow Green when
the Main receiver is active.
When the Main (VFO-A) receiver is active, pressing
this button momentarily will mute the receiver, and
the indicator will blink. Pressing the button once more
will restore receiver operation, and the indicator will
glow Green steadily.
TX Indicator/Switch
When this button is pushed, the indicator will glow
Red, and the transmitter will be engaged on the same
frequency and mode as was set up for the Main (VFO-
A) band (subject to any Clarifier offset, of course).
Advice
If this indicator is not illuminated, it means that the
Sub (VFO-B) TX indicator has been selected (it will
be glowing Red). In this case, transmission will be
effected on the frequency and mode programmed for
the Sub (VFO-B) band.
FRONT PANEL CONTROLS
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-DX9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-DX9000 in the language / languages: English as an attachment in your email.

The manual is 25,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info