674754
22
Zoom out
Zoom in
Previous page
1/156
Next page
Page 20 FT DX 9000D OPERATION MANUAL
FRONT PANEL CONTROLS
MOX Switch
Pressing this button engages the PTT (Push to Talk)
circuit, to activate the transmitter. It must be in the
undepressed position for reception. This switch repli-
cates the action of the Push to Talk (PTT) switch on
the microphone. When engaging the MOX switch,
or otherwise causing a transmission to be started, be
certain you have either an antenna or 50-Ohm dummy
load connected to the selected Antenna jack.
VOX Switch
VOX Operation: This button enables automatic voice-
actuated transmitter switching in the SSB, AM, and
FM modes. While activated, the LED inside this but-
ton glows red. The controls affecting VOX operation
are the front panel’s VOX and DELAY knobs
(see section ( ) below. By proper adjustment of these
controls, hands-free voice-actuated operation is pos-
sible.
DIM Switch
Press this button to lower the illumination intensity of
the analog meters, the frequency display, and the TFT.
Press it once more to restore full brightness.
Advice
Menu Items “DISPLAY 014 DIMMER-METER” and
“DISPLAY 015 DIMMER-VFD” allow you to con-
figure the dimming levels for the analog meters and
the frequency display/TFT independently, so you can
customize the brightness levels.
PHONES Jack
A 1/4-inch, 3-contact jack accepts either monaural or
stereo headphones with 2- or 3-contact plugs. When a
plug is inserted, the loudspeaker is disabled. With ste-
reo headphones such as the optional YH-77STA, you
can monitor both Main (VFO-A) and Sub (VFO-B)
receiver channels at the same time during Dual Re-
ceive operation.
Note: When wearing headphones, we recommend that
you turn the AF Gain levels down to their lowest set-
tings before turning power on, to minimize the impact
on your hearing caused by audio “pops” during switch-
on.
POWER Switch
Press and hold in this switch for two seconds to turn
the transceiver on, after first setting the rear panel
Power switch to the “
I
” position. Press and hold in
this switch for two seconds, similarly, to turn the trans-
ceiver off. If the rear panel’s Power switch is set to the
O
” position, the front panel POWER switch will
not function.
Advice
This is the actual power On/Off switch for turning on
the transceiver. When the rear panel’s Power switch is
set to the “
I
” position, power is supplied to the OCXO
to stabilize the reference oscillator, and the remainder
of the transceiver is set in a “stand-by” mode, await-
ing the command for the transceiver to switch on via
the front panel POWER switch. For further infor-
mation on the rear panel Power switch, please see the
discussion on page 36.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-DX9000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-DX9000 in the language / languages: English as an attachment in your email.

The manual is 25,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info