478504
114
Zoom out
Zoom in
Previous page
1/132
Next page
Page 112 FT-950 OPERATING MANUAL
041 A1A CW AUTO
Function: Enables/disables CW keying while operating
on SSB.
Available Values: OFF/50/On
Default Setting: OFF
OFF:Disables CW keying while operating on SSB.
50: Enables CW keying only while operating SSB on 50
MHz (but not HF).
On: Enables CW keying while operating on SSB (all TX
bands).
NOTE:
This feature allows you to move someone from SSB to
CW without having to change modes on the front panel.
042 A1A BFO
Function: Sets the CW carrier oscillator injection side for
the CW mode.
Available Values: USb/LSb/Auto
Default Setting: USb
USb: Injects the CW carrier oscillator on the USB side.
LSb: Injects the CW carrier oscillator on the LSB side.
Auto: Injects the CW carrier oscillator on the LSB side
while operating on the 7 MHz band and below, and
the USB side while operating on the 10 MHz band
and up.
043 A1A BK-IN
Function: Sets the CW “break-in” mode.
Available Values: SEni/FuLL
Default Setting: SEni
SEni (SEMI):The transceiver will operate in the semi
break-in mode. The delay (receiver recovery) time is set
via the Menu item “044 A1A DELAY”.
FuLL: The transceiver will operate in the full break-in
(QSK) mode.
044 A1A DELAY
Function: Adjusts the Keying Delay (receiver recovery)
time on the CW mode.
Available Values: 30 ~ 3000 msec (10 msec/step)
Default Setting: 200 msec
045 A1A PITCH
Function: Adjusts your preferred CW tone pitch.
Available Values: 300 ~ 1050 Hz (50 Hz/step)
Default Setting: 700 Hz
046 A1A WEIGHT
Function: Sets the Dot:Dash ratio for the built-in elec-
tronic keyer.
Available Values: (1:) 2.5 ~ 4.5
Default Setting: 3.0
047 A1A FRQDISP
Function: Selects the frequency Display Format for the
CW mode.
Available Values: dir/OFSt
Default Setting: OFSt
dir (Direct Frequency):Displays the receiver carrier fre-
quency, without any offset added.
When changing modes between
SSB and CW, the frequency dis-
play remains constant.
OFSt (Pitch Offset): This frequency display reflects the
added BFO offset.
048 A1A PC KYNG
Function: Enables/disables CW keying from the “DATA
PTT” terminal (pin 3) on the rear panel’s RTTY/PKT jack
while operating on the CW mode.
Available Values: EnA (Enable)/diS (Disable)
Default Setting: diS (Disable)
049 A1A QSKTIME
Function: Selects the time delay between when the PTT
is keyed and the carrier is transmitted during QSK opera-
tion when using the internal keyer.
Available Values: 15/20/25/30 msec
Default Setting: 15 msec
MENU MODE
MODE-CW GROUP
114


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-950 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-950 in the language / languages: English as an attachment in your email.

The manual is 6,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info