478500
11
Zoom out
Zoom in
Previous page
1/76
Next page
Page 9FT-897D OPERATING MANUAL
INSTALLATION
RF FIELD EXPOSURE
This transceiver is capable of power output in excess of 50
Watts, so customers in the United States may be required to
demonstrate compliance with Federal Communications
Commission (FCC) regulations concerning maximum per-
missible exposure to radio frequency energy. Compliance is
based on the actual power output used, feedline loss, an-
tenna type and height, and other factors which can only be
evaluated as a system.
Information regarding these regulations may be available
from your Dealer, your local radio club, from the FCC di-
rectly (press releases and other information can be found on
the FCC’s site on the World Wide Web at <http://
www.fcc.gov>), or from the American Radio Relay League,
Inc. (225 Main St., Newington CT 06111 or <http://
www.arrl.org>).
Although there is negligible radio frequency (RF) leakage
from the FT-897D transceiver itself, its antenna system
should be located as far away from humans and animals as
practicable, so as to avoid the possibility of shock due to
accidental contact with the antenna or excessive long-term
exposure to RF energy. During mobile operation, do not
transmit if someone is standing adjacent to your antenna,
and use the lowest power possible.
Never stand in front of an antenna (during testing or opera-
tion) when RF power is applied, especially in the case of
430 MHz directional arrays. The 20 Watt power output sup-
plied by the FT-897D, combined with the directivity of a
beam antenna, can cause immediate heating of human or
animal tissues, and may cause other undesirable medical
effects.
ELECTROMAGNETIC COMPATIBILITY
If this transceiver is used with, or in the vicinity of, a com-
puter or computer-driven accessories, you may need to ex-
periment with grounding and/or Radio Frequency Interfer-
ence (RFI) suppression devices (such as ferrite cores) to
minimize interference to your communications caused by
energy from the computer. Computer-generated RFI is usu-
ally a result of inadequate shielding of the computers cabi-
net or I/O and peripheral connections. While computer equip-
ment may “comply” with RF emission standards, this does
not ensure that sensitive Amateur Radio receivers like the
FT-897D will not experience interference from the device!
Be certain to use only shielded cables for TNC-to-Trans-
ceiver connections. You may need to install AC line filters
on the power cord(s) of the suspected equipment, and
decoupling ferrite toroidal chokes may be required on inter-
connecting patch/data cables. As a last resort, you can try
installing additional shielding within the computers case,
using appropriate conductive mesh or conductive shielding
tape. Especially check “RF holes” where plastic is used for
cabinet front panels.
For further information, consult amateur radio reference
guides and publications relating to RFI suppression tech-
niques.
HEAT AND VENTILATION
To ensure long life of the components, be certain to provide
adequate ventilation around the cabinet of the FT-897D.
The cooling system of the transceiver must be free to draw
cool air in from the side of the transceiver and expel warm
air from the rear of the transceiver.
Do not install the transceiver on top of another heat-gener-
ating device (such as a linear amplifier), and do not place
equipment, books, or papers on top of the transceiver. Place
the transceiver on a hard, flat, stable surface. Avoid heating
vents and window locations that could expose the transceiver
to excessive direct sunlight, especially in hot climates.
Heat Dust VentilationWater & Moisture
Note
Save the packing materials in case you need to trans-
port the set (on an airplane, etc.) and/or return the set
for service.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info