478500

Yaesu FT-897D Manual

7
Zoom out
Zoom in
Previous page
1/76
Next page
Page 5FT-897D OPERATING MANUAL
INSTALLATION
AC power source operation (requires optional FP-30 AC power supply)
POWER CONNECTIONS
For base station installations, Yaesu recommends the use of
the FP-30 AC power supply, which is designed to clamp
onto the FT-897D.
Installation
1. Turn the transceiver’s power off, and disconnect all
cables from the transceiver.
2. Remove the six screws (three screws on bottom side and
rear side), then lift off the bottom cover (Figure 1 and 2).
3. Attach the FP-30 to the bottom of the FT-897D, then
affix it in place with the six screws removed in the above
steps (Figure 3).
4. Connect the 6-pin Molex plug from the FP-30 to the
INPUT jack on the rear panel of the FT-897D (Figure
4).
5. Make sure that your AC voltage is correct and that the
FP-30 POWER switch is set to Off; connect the AC
power cable between the INPUT jack on the rear panel
of the FP-30 and a nearby AC wall outlet.
Operation
1. To turn the transceiver on, turn on the POWER switch
on the FP-30 before turning on the POWER switch on
the FT-897D.
2. To turn the transceiver off, turn off the POWER switch
on the FT-897D before turning off the POWER switch
on the FP-30.
When you do not use the FP-30 with the FT-897D
for a long time, disconnect the AC plug from the AC
wall outlet.
Figure 1
Figure 2
Figure 4
POWER Switch
Figure 3
AC Input Voltage Selection (U.S.A. Users only)
❒ Before moving the AC range switch, disconnect the FP-30’s AC Power
Cable from the AC line outlet, then wait 10 minutes to allow the power
supply’s electrolytic capacitors to discharge (electrical shock hazard!).
❒ Peel off the label on the side of the FP-30.
❒ Move the AC range switch to the “115” position for operation from
100-120 VAC, or to the “230” position for operation from 200-240 VAC.
❒ Always uses the 10 A Fuse in the fuse holder on the rear panel whether
operate on 100-120 VAC or 200-240 VAC. Do not use the improper
fuse.
Warning: Our Warranty does not cover damage caused by improper supply voltage nor use of an improper fuse.
Peel off the label
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info