478500
6
Zoom out
Zoom in
Previous page
1/76
Next page
Page 4 FT-897D OPERATING MANUAL
POWER CONNECTIONS
The FT-897D is designed use from (1) an external DC power source, (2) internal battery (requires optional FNB-78 Ni-MH
battery pack), or (3) AC power source (requires optional FP-30 Internal AC Power Supply).
External DC power source operation
INSTALLATION
The DC power connector for the FT-897D must only be
connected to a DC source providing 13.8 Volts DC (±15%),
and capable of at least 22 Amperes of current. Always ob-
serve proper polarity when making DC connections:
The Red DC power lead connects to the Positive (+)
DC terminal; and the Black DC power lead connects
to the Negative (–) DC terminal.
In mobile installations, noise pickup may be minimized by
connecting the DC cable directly to your vehicle’s battery,
rather than to the ignition switch or “accessory” circuitry.
Direct connection to the battery also provides the best volt-
age stability.
Tips for Successful Mobile Installations:
Before connecting the DC cable to the battery, measure
the voltage across the battery terminals with the engine
running fast enough to show a charge. If the voltage is
above 15 Volts, the vehicle’s voltage regulator should
be adjusted to reduce the charging voltage to 14 Volts or
lower.
Route the DC cable as far away from the ignition cables
as possible.
If the DC cable is not long enough, use #12 AWG (mini-
mum) stranded, insulated wire to extend it. Be certain to
solder the connections at the splice securely, and pro-
vide ample insulation for the soldered splice (heat shrink
tubing plus black electrical tape work well).
Check the battery terminal connections frequently to be
sure they are tight and not corroded.
When operating with the vehicle turned off, or operating
from a stand-alone car battery (in a camp site, etc.), be
mindful of the minimum operating voltage (11.73 Volts)
for the FT-897D. If the battery is not charged sufficiently
to maintain at least 11¾ Volts at the radio, erratic opera-
tion or shut-down may occur.
Caution
Permanent damage can result if improper supply volt-
age, or reverse-polarity voltage, is applied to the FT-
897D. The Limited Warranty on this transceiver does
not cover damage caused by application of AC voltage,
reversed polarity DC, or DC voltage outside the speci-
fied range of 13.8V ±15%. Never attempt to connect
the FT-897D to a 24 Volt battery system.
When replacing fuses, be certain to use a fuse of the
proper rating. The FT-897D requires a 25A fast-blow
fuse.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info