36023

Yaesu ft-897D Manual

37
Zoom out
Zoom in
Previous page
1/76
Next page
Page 35FT-897D OPERATING MANUAL
TRANSMITTER OPERATION
Tone Search Scanning
In operating situations where you don’t know the CTCSS
tone being used by another station, you can command the
radio to listen to the incoming signal and scan in search of
the tone being used. To scan for the CTCSS tone in use:
1. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row
“e”
[
TON, -----, TDCH
]
appears on the display.
2. Press the
[
A
](
TON
)
key to activate CTCSS Encoder/De-
coder; (the “TSQ” icon will appear on the display)
3. Press the
[
C
](
TDCH
)
key to start scanning for the in-
coming CTCSS tone.
4. When the radio detects the cor-
rect tone, it will halt on that tone,
and audio will be allowed to pass
5. The CTCSS tone detected will be
stored as the “current” tone, so it may be used for memory
storage purposes, and you may now exit to normal op-
eration.
you press the
[
A
](
TON
)
key repeatedly, you will ob-
serve “TSQ” (CTCSS Encode/Decode), “DEN” (Digi-
tal Coded Squelch, Encode), followed by “DCS”
(Digital Coded Squelch, Encode/Decode). One ad-
ditional press will disable all repeater-access tone
systems. See the next section for a discussion of DCS
operation.
• If the default repeater access tone is not appropriate
for the repeater on which you are operating, it may
be set easily:
1. Press and hold the
[
A
](
TON
)
key for one second.
This instantly recall Menu Mode No-083
[
TONE
FREQ
]
.
2. Rotate the DIAL knob to select the desired CTCSS
frequency.
FM TRANSMISSION
3. When done, press and hold the
[
F
]
key for one
second to save the new setting and exit to normal
operation.
5. With repeater shift activated, you can temporarily re-
verse the transmit and receive frequencies by pressing
the
[
B
](
REV
)
key in the Multi Function Row “d”
[
RPT,
REV, VOX
]
. The “–” icon will blink while “Reverse” shift
is activated. Press the
[
B
](
REV
)
key again to revert to
the “Normal” shift direction.
6. On many transceiver versions, the Automatic Repeater
Shift (ARS) feature is enabled at the factory. This fea-
ture automatically activates the appropriate repeater shift
when you are operating inside the designated 144 MHz
or 430 MHz FM repeater sub-bands in your country. If
you wish to change the On/Off settings for the ARS, use
Menu Mode No-002
[
144MHz ARS
]
or Menu Mode
No-003
[
430MHz ARS
]
(see page 56).
If your local repeaters need a 1750-Hz burst
tone for access (typically in Europe), press and
hold in the front panel’s
[
HOME
]
key to trans-
mit the burst tone (FM mode only).
CTCSS TONE FREQUENCY (Hz)
67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4
88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9
114.8 118.8 123.0 127.3 131.8 136.5 141.3 146.2
151.4 156.7 159.8 162.2 165.5 167.9 171.3 173.8
177.3 179.9 183.5 186.2 189.9 192.8 196.6 199.5
203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8
250.3 254.1
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu ft-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu ft-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info