36023
24
Zoom out
Zoom in
Previous page
1/76
Next page
Page 22 FT-897D OPERATING MANUAL
SETTING THE OPERATING FREQUENCY
1. In the “SSB/CW/DIG” modes, rotate the DIAL knob to
set the frequency. Clockwise rotation of the DIAL in-
creases the operating frequency.
2. In the “AM/FM/PKT” modes, rotate the MEM/VFO
CH knob to set the frequency. Clockwise rotation of the
MEM/VFO CH increases the operating frequency.
3. You may also use the MEM/VFO CH knob to adjust the
operating frequency in the “SSB/CW/DIG” modes. The
MEM/VFO CH knob provides faster tuning, ideal for
making quick changes in frequency when you want to
move across the band in a hurry. You can then use the
DIAL knob to make fine frequency adjustments.
The synthesizer steps for the MEM/VFO CH knob may be
adjusted independently by mode. Use Menu Mode No-006
[
AM STEP
]
for AM, No-052
[
FM STEP
]
for FM, and No-
082
[
SSB STEP
]
for SSB/CW/Digital. See pages 56, 59,
and 62 for details.
If you press the MEM/VFO CH knob momentarily, then
rotate the MEM/VFO CH knob, you can now change the
operating frequency in 1 MHz steps, allowing very quick
frequency excursions. This can be particularly helpful on
the VHF and UHF bands.
In step 2 above, it was mentioned that tuning in the “AM/
FM/PKT” modes is accomplished using the MEM/VFO CH
knob. By default, the DIAL is disabled in these modes; if
you wish to enable the DIAL in these modes, use Menu Mode
No-004
[
AM&FM DIAL
]
; see page 56.
The main DIAL synthesizers tuning rate (the
number of steps per rotation of the DIAL) can
be adjusted using Menu Mode No-035
[
DIAL
STEP
]
. See page 58 for details.
STACKED VFO SYSTEM
Press the
[
F
]
key momentarily, then rotate the MEM/VFO
CH knob, as needed, until Multi Function Row “a”
[
A/B,
A=B, SPL
]
appears on the display.
OPERATION
Now press the
[
A
](
A/B
)
key to toggle between the “A” and
B” VFOs. There are two such VFOs provided on each
Amateur band, so you may set VFO-A to the CW sub-band,
and VFO-B to the SSB sub-band, if you like. The operating
mode will be preserved, along with the frequency informa-
tion, on each VFO.
When changing bands on either the “A” or “B”
VFO, the two VFOs do not change bands to-
gether. This facilitates split-band operation,
such as on FM satellites.
CHANGING THE DIAL SPEED
By default, the FT-897D begins operation in the “fine tun-
ing” mode for the main tuning dial. However, a faster tuning
rate may be selected, for quick navigation up and down the
band.
BATT-B
BATT-A
DIAL MEM/VFO CH
BATT- A
BATT- B
BAND
MODE
CLARAF
LOC K
PHONE
MIC
SQL
/RF
MEM/VFO CH
DWN UP
V/M
DSP
UP
DSP
F
A F MEM/VFO CH
BATT-B
BATT-A
POWER
To engage the “Fast Tuning” mode, just press the POWER
switch momentarily while the transceiver is on. You will
observe a small “ ” icon in the bottom right-hand corner of
the LCD, and as you rotate the main tuning dial you will
notice that the tuning rate has increased significantly. Press
the POWER switch momentarily once more to return to the
“Slow Tuning” mode (the small “ ” will disappear).
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu ft-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu ft-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info