36023
12
Zoom out
Zoom in
Previous page
1/76
Next page
Page 10 FT-897D OPERATING MANUAL
LINEAR AMPLIFIER INTERFACING
The FT-897D provides the switching and drive-control lines
required for easy interfacing to most all commonly-avail-
able amplifiers sold today.
These include:
The Antenna Jacks (“HF/50MHz” and “144/430MHz”);
A T/R control line (open circuit on RX, closure to ground
on TX); and
A negative-going ALC jack (control voltage range: 0V
to –4V DC).
When interfacing to the VL-1000 Solid State 1 KW Lin-
ear Amplifier, the optional CT-58 Interface Cable pro-
vides for easy interconnection (requires that the Menu
Mode No-020
[
CAT/LIN/TUN
]
setting changes to “LIN-
EAR”).
The rear-panel CAT/LINEAR jack is an 8-pin, miniature
DIN type, with the “TX GND” pin providing a closure to
ground on transmit, for T/R control of your linear amplifier.
The ACC jack is a miniature stereo type, with external ALC
input capability on the tip connection. The main shaft is the
ground return. The ring connection of the ACC jack, when
closed to ground, places the FT-897D into the transmit mode,
and sends a steady CW carrier, for amplifier (or antenna
tuner) adjustment purposes.
Typical amplifier interface circuits are shown below.
Note that some amplifiers, particularly VHF or UHF “brick”
amplifiers, offer two methods of T/R switching: application
of +13V or a closure to ground.
Be sure to configure your amplifier so that it switches via a
closure to ground, as provided by your FT-897D’s CAT/
LINEAR jack (“TX GND” pin). Alternatively, many of these
amplifiers use “RF Sensing” to control their relays; if yours
is in this category, you may then use the T/R control line
from the “TX GND” pin of the CAT /LINEAR jack for
control of your HF linear amplifier, and RF sensing for your
VHF or UHF amplifier.
The “TX GND” T/R control line is a transistor “open col-
lector” circuit, capable of handling positive amplifier relay
coil voltages of up to +50V DC and current of up to 400
mA. If you plan on using multiple linear amplifiers for dif-
ferent bands, you must provide external band-switching of
the “TX GND” relay control line from the CAT/LINEAR
jack.
Important Note!
Do not exceed the maximum voltage or current ratings
for the “TX GND” line at the CAT/LINEAR jack. This
line is not compatible with negative DC voltages, nor
AC voltages of any magnitude.
Most amplifier control relay systems require only low
DC voltage/current switching capability (typically, +12V
DC at 25 ~ 75 mA), and the switching transistor in the
FT-897D will easily accommodate such amplifiers.
INSTALLATION
ANT 1
ANT 2
REMOTE
ON
OFF
BAND DATA 1
BAND DATA 2
GND
ALC 2
ALC 1
PTT 2
PTT 1
INPUT 1
INPUT 2
CONTROL
DC48V IN
To HF Antenna
To HF Antenna
To 50 MHz Antenna
INPUT 1
VL-1000
ANT 1
ANT 2
ANT 3
BAND-DATA 1
CAT
/LINEAR
To 144 / 430 MHz Antenna
ALC 1
CT-58 BAND DATA Cable
CT-58 ALC Cable
GND
DC 48V IN
CONTROL
*The “CT-58” consists of two separate cables: the BAND DATA cable (Part # T9101500) and the ALC Cable (T9101501).
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu ft-897D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu ft-897D in the language / languages: English as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info