674792
33
Zoom out
Zoom in
Previous page
1/68
Next page
FT-252 OperaTing Manual 31
Memory Scanning
Memory scanning is similarly easy to initiate:
1. Select the Memory mode by pressing the
[
V/M
]
key, if necessary.
2. Press and hold in either the
[
p
]
or
[
q
]
key for one second to initiate upward or
downward scanning, respectively.
3. If and when the scanner encounters a signal strong enough to open the squelch, the
scanner will halt temporarily; the decimal point of the frequency display will blink
during this “Pause” condition.
4. The scanner will then resume according to the Scan-Resume mode selected in the
previous section.
5. To cancel scanning, press the
PTT
switch.
How to Skip (Omit) a Channel during Memory Scan Operation
As mentioned previously, some continuous-carrier stations like a Weather Broadcast sta-
tion will seriously impede scanner operation if you are using the “Carrier Drop” Scan-
Resume mode, as the incoming signal will not pause long enough for the transceiver to
resume scanning. Such channels may be “Skipped” during scanning, if you like:
1. Recall the Memory Channel to be skipped during scanning.
2. Press the
[
SET/ATS
]
key to enter the Set mode.
3. Rotate the
DIAL
knob or press the
[
p
]
/
[
q
]
key to select Set Mode Item 38:
SKIP
.
4. Press the
[
SET/ATS
]
key momentarily enter the “Skip” channel-selection mode.
5. Rotate the
DIAL
knob or press the
[
p
]
/
[
q
]
key to select
SKIP
”. The current Memory Channel will now be ig-
nored during scanning. The
ONLY
selection is used for
“Preferential Memory Scan,” described in the next sec-
tion.
6. When you have made your selection, press the
PTT
switch to save the setting and
exit to normal operation.
When you recall the “skipped” memory channel manually, a
small
icon will appear at the left of the memory channel
number, indicating it is to be ignored during scanning.
To re-institute a channel into the scanning loop, select
OFF
in step 5 above (the “Skipped” channel will, of course, still be accessible via manual
channel selection methods using the
DIAL
knob in the MR mode, whether or not it is
locked out of the scanning loop).
Scanning
honbun_130313.indd 31 2013/03/13 19:47:59
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Yaesu FT-252 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-252 in the language / languages: English as an attachment in your email.

The manual is 5,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info