Manual Yaesu FT-2000D (page 126 of 140) (English)

478497

126

Zoom out

Zoom in

1/140

Page 124 FT-2000D OPERATING MANUAL

MODE-SSB GROUP

084 J3E MIC SEL

Function: Selects the microphone to be used on the SSB

modes (LSB and USB).

Available Values: Frnt / dAtA / PC

Default Setting: Frnt

Frnt (FRONT): Selects the microphone connected to

the front panel’s MIC jack while using

the SSB modes.

dAtA: Selects the microphone connected to

pin 1 of the PACKET Jack while us-

ing the SSB modes.

PC: This parameter is for future expansion

of this transceiver’s capabilities, but at

this time is not supported.

085 J3E TX BPF

Function: Selects the audio passband of the DSP modula-

tor on the SSB mode.

Available Values: 1-30 / 1-29 / 2-28 / 3-27 / 4-26 / 3000

1-30: 50-3000(Hz)

1-29: 100-2900(Hz)

2-28: 200-2800(Hz)

3-27: 300-2700(Hz)

4-26: 400-2600(Hz)

3000: 3000WB

Default Setting: 3-27 (300-2700 Hz)

NOTE:

The apparent power output, when using the widest band-

widths, may seem lower. This is normal, and it occurs be-

cause the available transmitter power is distributed over a

wider bandwidth. The greatest compression of power out-

put, conversely, occurs when using the “4-26” setting (400-

2600 Hz), and this setting is highly recommended for con-

test or DX pile-up work.

086 J3E LSB CAR

Function: Adjusts the receiver carrier point for the Main

band’s (VFO-A) LSB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/steps)

Default Setting: 0 Hz

087 J3E USB CAR

Function: Adjusts the receiver carrier point for Main

band’s (VFO-A) USB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/step)

Default Setting: 0 Hz

088 J3E SLSB CR

Function: Adjusts the receiver carrier point for the Sub

band’s (VFO-B) LSB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/step)

Default Setting: 0 Hz

089 J3E SUSB CR

Function: Adjusts the receiver carrier point for Sub band’s

(VFO-B) USB mode.

Available Values: –200 Hz ~ +200 Hz (10 Hz/step)

Default Setting: 0 Hz

RX AUDIO GROUP

090 rout AGC SLP

Function: Selects the gain curve of the AGC amplifier.

Available Values: nor / SLP

Default Setting: nor

nor (NORMAL): The AGC output level will follow a

linear response to the antenna input

level, while AGC is activated.

SLP (SLOPED): The AGC output level will increase

at 1/10 the rate of the antenna input

level, while AGC is activated.

MENU MODE

NORMAL

Input Signal

utput

SLOPE

091 rout HEADPHN

Function: Selects one of three audio mixing modes when

using headphones during Dual Receive operation.

Available Values: SEP / Con1 / Con2

Default Setting: SEP

SEP (SEPARATE): Audio from the Main (VFO-A)

receiver is heard only in the left

ear, and Sub (VFO-B) receiver

audio solely in the right ear.

Con1 (COMBINE 1): Audio from both Main (VFO-

A) and Sub (VFO-B) receivers

can be heard in both ears, but

Sub (VFO-B) audio is attenu-

ated in the left ear and Main

(VFO-A) audio is attenuated in

the right ear.

Con2 (COMBINE 2): Audio from both Main (VFO-

A) and Sub (VFO-B) receivers

is combined and heard equally

in both ears.

My FT2000D will not Transmit. Have not used it in over a year. I am sure it is something I have done wrong. Whe u puss PTT the signal goes to ZERO. Please Advise! Submitted on 12-9-2020 at 00:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Yaesu FT-2000D in the language / languages: English as an attachment in your email.

The manual is 7,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Yaesu FT-2000D Manual

Product: