765110
23
Zoom out
Zoom in
Previous page
1/28
Next page
TR3.0 Treadmill
21
Belt/Deck Lubrication Procedure
First, you want to clean between the belt and deck to remove any debris that may be trapped.
Use a clean, non-fraying rag, t-shirt, or light towel. Halfway between the end of the treadmill
and motor cover, shove the garment under the belt until you can grasp it on both sides of the
belt. Drag the garment the length of the entire belt 1-2 times. Remove the garment.
Do not lubricate with anything other than XTERRA Fitness approved lubricant. Your treadmill
comes with one tube of “Lube” and extra tubes can be ordered directly from
www.xterratness.com.
Keeping the deck lubricated at the recommended intervals ensures the longest life possible
for your treadmill. If the lubricant dries out, the friction between the belt and deck rises and
places undue stress on the drive motor, drive belt and electronic motor control board, which
could result in failure of these components. Failure to lubricate the deck at regular intervals
may void the warranty.
The belt & deck come pre-lubricated and subsequent lubrication should be performed every
90 hours of use or if you notice that the deck is dry. It is recommended that you reach be-
tween the belt and deck to verify there is lubrication present, every other month. If you check
and there isn’t any lubrication present, follow the procedure below even though the “Lube”
indicator isn’t lit on the console. Otherwise, lubricate when the console’s lubrication reminder
lights after 90 hours of use. Use the following procedure to apply the silicone lubricant:
1. Turn the power switch off and unplug the power cord from the wall outlet
2. Measure 18” from the edge of the motor cover; kneel down and reach under the belt
approximately 4- 6” from one edge. Squirt a line of lubricant about 1/8” wide x 15” long
in an “S” pattern perpendicular to the motor cover.
3. Repeat the process on the opposite side.
4. Plug the electrical cord back into the outlet and turn the power switch on.
5. Walk on the belt at a moderate speed for ve minutes to evenly distribute the silicone
lube.
6. Note: If the “Lube” message appears on the console, perform the following procedure to
reset the message:
1. To enter the Engineering Mode Menu press and hold down the Start, Stop and
Enter keys, then at the same time insert the safety key. Keep holding the keys down
until the Display displays Engineering Mode Menu. Press the Enter key to access
2. Press the Speed 5 key (or Speed 6 key to go backwards) until “Functions”
appears; press Enter
3. Press the Speed 5 key until “Reset Lube” message appears; press Enter
4. Press Stop to exit Engineering mode and resume use of your treadmill
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Xterra TR3.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Xterra TR3.0 in the language / languages: English as an attachment in your email.

The manual is 1,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info