673279
9
Zoom out
Zoom in
Previous page
1/40
Next page
Belt sander EN
98
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE
The machine is intended for dry sanding–with
high removal capacity–of wood, plastic, metal,
filler as well as varnished surfaces.
1. ON/OFF SWITCH
Depress to start and release to stop your tool.
2. SWITCH LOCK-ON BUTTON
(See Fig. A)
Depress on/off switch (2) then lock on button
(3). Your tool is now locked on for continuous
use. To switch off your tool just depress and
release the on/off switch.
3. VARIABLE SPEED CONTROL DIAL
Adjust the variable speed control (1) to
increase or decrease the speed according to
the material and sanding belt specification
to be used (also possible during no load
operation). See the table below for general
guidance on speed selection. Avoid prolonged
use at very low speed as this may damage
your sanders motor.
Material Speed selection Belt grit
Solid wood 5-6 80
Veneer 2-4 150
Chipboard 1-5 60/80
Plastics 2-5 100
Steel 5-6 80
Paint
removal
6 40/60
Balsa wood 1-3 100
Acrylic 1-2 100
4. CHANGING A SANDING BELT (See Fig. B, C)
WARNING!WARNING! Remove the
main plug from the socket before
changing sanding belt.
Pull the lever (7) to release the belt tension.
Remove and fit a new belt over both rollers.
Ensure the direction of rotation arrows on the
belt and the sander are the same. Close the
lever to tension the belt.
5. BELT CENTERING CONTROL (See Fig. D)
WARNING! Wear eye protection
before carrying out a belt centering
adjustment.
Turn the machine upside down, hold it firmly
with one hand, start the motor and release the
switch immediately after observing tracking
of sanding belt. If abrasive belt runs outward,
turn tracking adjustment knob counter-
clockwise and clockwise if belt runs inward.
Adjust the belt until the outer edge of the belt
is even with the outer edge of the base-plate
(12). Belt life will be greatly increased by
keeping the tracking adjustment set properly.
6. DUST BAG (See Fig. E)
Always operate your sander with the dust bag
fitted. For the best performance always empty
the dust bag in time. Remove the shaft from
the dust bag and shake out dust. To remove
the bag, slide the mounting bracket out and
away from the sander. To refit the bag, firmly
push the mounting bracket into the location
on the sander housing.
7. ASSEMBLE THE DUST EXTRACTION
ADAPTER (See Fig. F, G)
Your sander is equipped with two dust
extraction adapters, which are designed for
connecting the hose of a vacuum cleaner.
Insert the 35mm adapter (13a) into the outlet
until it is secured (See F), then insert the 32
mm adapter (13b) into the back of the 35 mm
adapter (Fig. G).
8. DRIVE BELT REPLACEMENT.
WARNING! Remove the main plug
from the socket before carrying out
a drive belt replacement.
Remove the three screws and the belt cover.
Carefully cut the drive belt if not already
broken and remove from your belt sander. Fit
your new drive belt around the large pulley.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX661.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX661.1 in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info