Manual Worx WX646.1 (page 7 of 76) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575091

Zoom out

Zoom in

1/76

Palm sander EN

76 PB7

Do not allow your sander to remain in the

same position otherwise you will remove

material and create and uneven surface.

6. CHANGE THE BASES (See Fig. C, D)

1) Remove the 5 Phillips head screws holding

the triangular base.

2) Replace triangular base by fastening the

detail sanding attachment to base position.

3) Fix it by 5 screws.

4) Similar process is conducted when detail

sanding attachment is changed to triangular

base.

7. ATTACH SANDING SHEETS AND PADS

(See Fig. E)

This sander features an easy hook and loop

accessory fastening system for quick changing

without clamps.

1) Unplug the sander.

2) Carefully center the sanding sheet (A) or

pad over the base (3/4) to be used. Line up the

tip of the sanding sheet (B) or pad with the tip

of the base (C).

3) Press the sheet or pad ﬁrmly in place.

4) To remove sheet or pad, simply pull it off.

WARNING: Failure to unplug the

sander could result in accidental starting

causing possible serious personal injury.

8. SANDING WITH EITHER BASE

(See Fig. F)

Always hold the sander as shown in Fig F.

Move the sander in long, sweeping strokes

across the sanding surface. Light pressure is

needed for sanding, polishing and scrubbing.

Let the sander do the work. Always check your

work. This sander removes material quickly.

IMPORTANT: Applying excessive

pressure will slow the sander and produce

unsatisfactory results.

WORK HINTS FOR YOUR

PALM SANDER

If your power tool becomes too hot, run no

load for 2-3 minutes to cool the motor.

Always ensure the work-piece is ﬁrmly held or

clamped to prevent movement.

Any movement of the material may affect the

quality of the sanding ﬁnish.

Start your sander before sanding and turn off

only after stopping sanding. For best results

sand wood in the direction of the grit.

Do not start sanding without sandpaper ﬁtted.

Do not allow the sandpaper to wear away, it

will damage the base-plate. The guarantee

does not cover base-plate wear and tear.

Use coarse grit paper to sand rough surfaces,

medium grit for smooth surfaces and ﬁne grit

for the ﬁnal surfaces. If necessary, ﬁrst make a

test on scrap material.

Use only good quality sandpaper.

The sanding efﬁciency is controlled by the

sandpaper not the amount of force you apply

to the tool. Excessive force will reduce the

sanding efﬁciency and cause motor overload.

Replacing the sanding paper regularly will

maintain optimum sanding efﬁciency.

MAINTENANCE

Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Your power tool requires no additional

lubrication or maintenance.

There are no user serviceable parts in your

power tool. Never use water or chemical

cleaners to clean your power tool. Wipe clean

with a dry cloth. Always store your power tool

in a dry place. Keep the motor ventilation slots

clean. Keep all working controls free of dust.

Occasionally you may see sparks through the

ventilation slots. This is normal and will not

damage your power tool.

If the supply cord is damaged, it must be

replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order to

avoid a hazard.

ENVIRONMENTAL

PROTECTION

Waste electrical products should not

be disposed of with household waste.

Please recycle where facilities exist.

Check with your local authorities or retailer for

recycling advice.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX646.1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX646.1 Manual

Product: