575077
11
Zoom out
Zoom in
Previous page
1/104
Next page
12V Li-Ion multi-purposed saw EN
1110
light will be red to indicate the charging
process has started.
3) On completion of charge, the light will turn
to be green. The pack is now fully charged,
unplug the charger and remove the battery
pack.
4. TO REMOVE OR INSTALL BATTERY
PACK (See Fig. B)
Locate the battery release buttons (11) on
side of battery pack and depress both sides
to release the battery pack from your tool.
Remove the battery pack from your tool. After
it has recharged insert the battery pack into
the battery port. A simple push and slight
pressure will be sufficient.
ADJUSTMENT
Function of this tool is the combination of
a jigsaw and a reciprocating saw, which is
realized by operating the pivot release lever
(4).
Lift up the pivot release lever to full until it
cannot be lifted. (See Fig. C)
Rotate the front portion of the tool into any of
the SIX positions (0, 18, 36, 54, 72 and 90deg)
(See Fig. D). Restore the pivot release lever.
In Position I, this tool can be worked as a
jigsaw.
In Position VI, this tool can be worked as a
reciprocating saw.
WARNING!
When adjusting the tool, you can only
hold the foot plate (9) as shown in Fig.E1.
Never hold the pivot head as shown in Fig.
E2, E3.
WARNING!
To avoid being pinched, keep hands away
from the hinge when changing positions.
To avoid tool being turned on accidentally,
make sure keep your hands away from the
lock-off button.
REPLACING / INSERTING THE SAW
BLADE
Before any work on the machine itself,
remove the battery.
The blade (15) should extend past the foot
plate and the thickness of the workpiece
during the cut. Select the blade best suitable
for the material to be cut and use the shortest
blade suited for the thickness of the material.
WARNING! Cut hazard. Blade
breakage may occur if the blade
does not extend past the foot plate and the
workpiece during the cut. Increased risk of
personal injury, as well as damage to the foot
plate and workpiece may result.
CAUTION: Keep your hands away from the
lock-off button to prevent switch actuation
before making any adjustments or removing
or installing attachments or accessories.
— INSERTING THE SAW BLADE
(See Fig. F-H)
Wear protective gloves when assembling
the saw blade. Contact with the saw
blade can lead to injuries. You can only
use the blade type shown in Fig F.
The machine is equipped with a tool-free
blade holder (7). This makes possible easy and
quick changing of the saw blade without any
additional tools.
Rotate the ring counterclockwise and hold in
position. Fully insert the blade into the blade
holder slot with blade teeth facing forward
then release the ring, which will self-rotate
and clamp over the top of the blade. (See Fig.
G1&G2)
— REMOVING THE SAW BLADE
To remove a blade, hold the blade and rotate
the blade holder ring counterclockwise to
release the blade.
WARNING: The blade may be spring
ejected so protect your eyes.
NOTE: When using JIGSAW MODE (90 deg) ,
the blade teeth face forward as shown in Fig. H.
OPERATION
WARNING: Always wear eye protection
while operating this or any other power
tool.
WARNING: Burn hazard. Do not touch
the blade immediately after use. Contact
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX540.9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX540.9 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info