Manual Worx WX372 (page 10 of 96) (English, German, Dutch, French, Italian, Polish, Spanish)

575018

Zoom out

Zoom in

1/96

Lithium-Ion cordless hammer drill EN

1110

left). Only use reverse rotation marked “ ”

(lever is moved to the right) to remove screws

or release a jammed drill bit.

WARNING: Never change the

direction of rotation when the

chuck is rotating, wait until it has

stopped!

4. TWO-SPEED GEAR CONTROL (See Fig.C)

The drill has a Two-Speed Gear Control (3)

designed for drilling or driving at LO (mark is

1) or HI (mark is 2) speeds. A slide switch is

located on top of the drill to select either LO

or HI speed. When using the drill in the LO

speed range, the speed will decrease and the

drill will have greater power and torque. When

using the drill in the HI speed range, the speed

will increase and the drill will have less power

and torque.

Gear I

Low speed range: for screwdriving or working

with large drilling diameter.

Gear II

High speed range: for working with small

drilling diameter.

WARNING: To prevent gear damage,

always allow the chuck to come

to a complete stop before changing the

direction of rotation or the two-speed

gear train.

5. CHUCK ADJUSTMENT (See Fig.D)

To open the chuck jaws rotate the front section

of the chuck (1). Insert the drill bit between

the chuck jaws and rotate the front section in

the opposite direction. Ensure the drill bit is

in the center of the chuck jaws. Finally, ﬁrmly

rotate the front chuck section in the opposite

directions. Your drill bit is now clamped in the

chuck.

6. TORQUE ADJUSTMENT AND HAMMER

OR DRILLING CONTROL (See Fig.E)

(Screw driving force of your drill driver)

The torque is adjusted by rotating the torque

adjustment ring (2). The torque is greater

when the torque adjustment ring is set on

a higher setting. The torque is less when

the torque adjustment ring is set on a lower

setting.

When drilling in masonry and concrete choose

the hammer position

When drilling in wood, metal, plastic and

screwdriver choose the drill position .

Make the setting as follows:

1 - 4 for driving small screws

5 - 9

for driving screws into soft

material

10 - 14

for driving screws into soft and

hard material

15 - 19 for driving screws into hard wood

20 - 22 for driving larger screws

for heavy drilling

for drilling in Brickwork and

concrete

7. AUTOMATIC SPINDLE LOCK

The automatic spindle lock allows you to

use as a regular screwdriver. You can give an

extra twist to ﬁrmly tighten a screw, loosen

a very tight screw or continue working

when the battery energy has expired. For

manual screwdriver purposes, the chuck is

automatically locked when the tool is off.

8. SIGHT LIGHT

The Sight Light (8) allows you to keep a clear

view under less illuminated circumstances.

To turn on the light simply press the on/off

switch. When you release the on/off switch,

the light will go out.

9. DRILLING

Drilling

Set the Torque adjustment ring to the “Drilling

without impact” symbol . The safety clutch is

deactivated in the “Drilling” position.

Impact Drilling

Set the Torque adjustment ring to the “Impact

drilling” symbol . In the “Impact drilling”

position, the safety clutch is deactivated and

the maximum power is always effective.

Move the drill bit into the workpiece, applying

only enough pressure to keep the bit cutting.

Do not force or apply side pressure to

elongate a hole.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX372 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX372 Manual

Product: