Manual Worx WX312 (page 9 of 84) (English, German, Dutch, French, Italian, Polish, Spanish)

575023

Zoom out

Zoom in

1/84

Impact drill EN

OPERATION

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for impact drilling in

brick, concrete and stone as well as for drilling

in wood, metal and plastic.

1. AUXILIARY HANDLE (See Fig. A)

Slide the handle onto the drill and rotate

to the desired working position. To clamp

the auxiliary handle rotates the handgrip

clockwise. To loosen the auxiliary handle

rotate the hand grip anti-clockwise. Always

use the auxiliary handle.

WARNING! Always check and

rotate the handle tightly before

using to avoid any accident.

2. INSTALLING THE DEPTH GAUGE

(See Fig. B)

The depth gauge can be used to set a constant

depth to drill. To use the depth gauge, loosen

the handle by rotating the bottom section of

handle anti-clockwise. Insert the depth gauge

through hole in handle. Slide the depth gauge

to required depth and tighten fully.

3. INSERTING A TOOL INTO CHUCK

(See Fig. C1, C2, C3)

KEY CHUCK (1) (WX312)

Remove chuck key from key storage tab at base

of drill handle, place key into chuck, turn key

anti-clockwise to undo/loosen chuck, inset drill/

tool and ﬁrmly tighten chuck by turning key

clockwise. Remove key and replace in storage

tab at base of drill handle.(See Fig. C1)

KEYLESS CHUCK (9) (WX312.1)

First pull the locking sleeve (a) backward until

you hear a “click” sound. Then, while holding

the locking sleeve, rotate and loosen the front

section of the chuck to open the chuck jaws.

Insert the drill bit into the chuck jaws, and while

holding the locking sleeve, rotate and tighten

the front section in the opposite direction.

Ensure that the drill bit is in the center of the

chuck jaws. Finally, push the locking sleeve

forward until you hear a “click” sound. Your

drill bit is now locked in the chuck.

(See Fig.C2,C3)

4. ON/OFF SWITCH

Depress the switch to start the tool and

release it to stop your tool.

5. SWITCH LOCK-ON BUTTON (See Fig. D)

Depress on/off switch then lock-on button,

release on/off switch ﬁrst and lock-on button

second. Your switch is now locked on for

continuous use. To switch off your tool just

depress and release the on/off switch.

6. VARIABLE SPEED CONTROL

(See Fig. E)

Adjust the variable speed control to increase

or decrease the speed according to the

material and accessory to be used (also

possible during no load operation). Low speed

will provide low torque and high speed gives

higher torque.

7. FORWARD AND REVERSE ROTATION

CONTROL (See Fig. F)

For drilling use forward rotation marked “

”

(lever is moved to the left). Only use reverse

rotation marked “ ” (lever is moved to the

right) to remove screws or release a jammed

drill bit.

NOTE: Never move the forward/reverse

switch whilst the drill in operation or

the on/off switch is locked as this will

damage the drill.

8. HAMMER OR DRILLING CONTROL

(See Fig. G)

When drilling masonry and concrete push

the drill/impact action selector switch into the

hammer position “

”. When drilling wood,

metal, plastic push the switch into the drill

position “ ”.

WORKING HINTS FOR YOUR

DRILL

1. Drilling masonry and concrete

Select the drill/impact action selector switch

to the “hammer symbol” position. Tungsten

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX312 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 1,64 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX312 Manual

Product: