575013
12
Zoom out
Zoom in
Previous page
1/120
Next page
3 in1 drill/driver/impact driver EN
1312
or “ . The adjusting ring can be
aligned in any torque levels for this operation.
The drill has a two-speed gear control
designed for drilling or driving at LO (mark
is ) or HI (mark is ) speed (See Fig. E2).
When using the drill in the LO speed range,
the speed will decrease and the drill will have
greater power and torque. When using the
drill in the HI speed range, the speed will
increase and the drill will have less power and
torque.
WARNING: To prevent gear damage,
always allow the chuck to come
to a complete stop before changing the
direction of rotation or the two-speed
gear control.
When drilling into a hard smooth surface,
use a center punch to mark the desired hole
location. This will prevent the drill bit from
slipping off center as the hole is started. Hold
the tool firmly and place the tip of the bit at
the point to be drilled. Depress the switch
trigger to start the tool. Move the drill bit into
the workpiece, applying only enough pressure
to keep the bit cutting. Do not force or apply
side pressure to elongate a hole.
Tungsten carbide drill bits should
always be used for concrete and
masonry. When drilling in metal, only use
HSS drill bits in good condition. Always
use a magnetic bit holder (not included)
when using short screwdriver bits. When
screw-driving, apply a small quantity
of liquid soap or similar to the screw
threads to ease insertion.
IMPACT DRIVER OPERATION
Slide the function mode selection switch (9) to
mark “ ”.
The adjusting ring can be aligned in any
torque levels for this operation.
8. DISPOSAL OF AN EXHAUSTED
BATTERY PACK
Li
To preserve natural resources, please
recycle or dispose of the battery pack
properly. This battery pack contains
Lithium batteries. Consult your local waste
authority for information regarding available
recycling and/or disposal options. Discharge
your battery pack by operating your tool, then
remove the battery pack from the tool housing
and cover the battery pack connections with
heavy-duty adhesive tape to prevent short
circuit and energy discharge. Do not attempt
to open or remove any of the components.
9. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop.
Relieve the load on the machine immediately
and allow cooling for approx. 30 seconds at
the highest no-load speed.
10. TEMPERATURE DEPENDENT
OVERLOAD PROTECTION
When using as intended for the power tool
cannot be subject to overload. When the
load is too high or the allowable battery
temperature of 75°C is exceeded, the
electronic control switches off the power
tool until the temperature is in the optimum
temperature range again.
11. PROTECTION AGAINST DEEP
DISCHARGING
The Li-Ion battery is protected against deep
discharging by the “Discharging Protection
System”. When the battery is empty, the
machine is switched off by means of a
protective circuit: The inserted tool no longer
rotates.
MAINTENANCE
Your power tool requires no additional
lubrication or maintenance.
There are no user serviceable parts in your
power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool
in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
Occasionally you may see sparks through the
ventilation slots. This is normal and will not
damage your power tool.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX283.3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX283.3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info