Manual Worx WX283.3 (page 11 of 120) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575013

Zoom out

Zoom in

1/120

3 in1 drill/driver/impact driver EN

1110

2. ON / OFF SWITCH (See

Fig.

Depress the On/Off switch (5) to start and

release it to stop your tool. The on/off switch is

ﬁtted with a brake function which stops your

chuck immediately when you quickly release

the switch.

It is also a variable speed switch that delivers

higher speed and torque with increased

trigger pressure. Speed is controlled by the

amount of switch trigger depression.

WARNING: Do not operate for

long periods at low speed because

excess heat will be produced internally.

3. SWITCH LOCK

The switch trigger can be locked in the OFF

position. This helps to reduce the possibility of

accidental starting when not in use. To lock the

switch trigger, place the rotation control in the

center position.

4. REVERSIBLE (See Fig. C)

For drilling and screw driving use forward

rotation marked “ ” (lever is moved to the

left). Only use reverse rotation marked “ ”

(lever is moved to the right) to remove screws

or release a jammed drill bit.

WARNING: Never change the

direction of rotation when the

chuck is rotating, wait until it has

stopped!

5. CHUCK ADJUSTMENT (See Fig. D)

Detachable chuck is suggested for using in the

drill mode.

To open the chuck jaws, ﬁrmly hold the rear

sleeve of the chuck, and then rotate the

front sleeve. Insert the drill bit between the

chuck jaws and rotate the front sleeve in the

opposite direction. Ensure the drill bit is in the

center of the chuck jaws. Finally, hold the rear

sleeve of the chuck and ﬁrmly rotate the front

sleeve in the opposite directions. Your drill bit

is now clamped in the chuck.

6. USING THE LED LIGHT

To turn on the light simply press the on/off

switch. When you release the on/off switch,

the light will be off.

LED lighting increases visibility-great for

dark or enclosed area. LED is also a battery

capacity indicator. It will ﬂash when power

gets low.

7. FUNCTION MODE SELECTION

The operation of the tool for each application

is set with the function mode selection switch

(9). To change between functions, slide the

function mode selection switch (9) to the

desired operating mode as follows:

Screwdriver mode (See Fig. E1)

Drill driver mode (See Fig. E2)

Impact driver mode (See Fig. E3)

WARNING: When using the function

mode selection switch, use only when

the tool stops. But when the switch does not

easily move, depress the On/off switch slightly

to rotate the spindle and then move the

function mode selection switch.

SCREWDRIVING OPERATION

Slide the function mode selection switch (9) to

mark“ ”. Adjust the adjusting ring (8) to the

proper torque level for your work.

The torque is adjusted by rotating the torque

adjustment ring (See Fig. F). The torque is

greater when the torque adjustment ring is set

on a higher setting. The torque is less when

the torque adjustment ring is set on a lower

setting.

Make the setting as follows:

1 - 4 For driving small screws

5 - 9

For driving screws into soft mate-

rial

10 - 14

For driving screws into soft and

hard material

15 - 19 For driving screws into hard wood

20 - 22 For driving larger screws

DRILLING OPERATION

Slide the function mode selection switch (9)

to mark

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX283.3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX283.3 Manual

Product: