575025

Worx WX254 Manual

12
Zoom out
Zoom in
Previous page
1/104
Next page
12
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE
The power tool is intended for driving in and loosening
screws as well as for drilling in wood, metal and plastic.
1. BEFORE OPERATING THIS TOOL
A) CHARGE THE BATTERY
The battery charger supplied is only for the Li-ion battery
installed in the machine. Do not use another battery
charger.
The Li-ion battery is protected against deep discharging.
When the battery is empty, the machine is switched off by
means of a protective circuit: The chuck no longer rotates.
When the Battery Pack is charged for the first time or after
prolonged storage, the Battery Pack will accept a 100%
charge after several charge and discharge cycles.
B) CHARGING (See Fig. A)
The screwdriver has two ways to charge.
1. Plug the Charger into a suitable power outlet. Next,
connect the screwdriver to the Battery Charger at the
Charging Socket. The Indicator will illuminate Red
during charging.
2. Recharge the screwdriver from the charging base.
Follow the same steps as above, plug the charger
plug into a suitable power outlet, the indicator won’t
illuminate. Next, connect the base with the battery
charger, the indicator (Red) will illuminate during
charging.
Let the battery charge for 3-5 hours. The battery is fully
charged as soon as the indicator is no longer lit. Then
unplug the Charger. Disconnect the Charger from the
screwdriver. The screwdriver is ready to be used.
IMPORTANT:
When charging, the Charger and screwdriver may
become warm to the touch; this is normal and does not
indicate a problem.
2. OPERATING INSTRUCTIONS
Inspect the Screwdriver before using to ensure all the
parts are running smoothly and there are no abnormal
sounds or sparks. Before driving fasteners, check behind
walls for wires and other electrical hazards or plumbing.
OPERATION
1. INSERTING THE BIT CARTRIDGE
(See Fig. B)
Pull the Cover back completely to insert the Bit Cartridge
(7).
2. SELECTING A BIT
1. Slide the Cover fully open, past the red line on the
tool. The Bit Cartridge will advance automatically.
(The Bit Cartridge can be manually rotated to left
direction if preferred.) (See Fig. C1, C2).
2. Move the top Cover back and forth until the desired
Bit Is in place.
If the Bits in the Bit Cartridge need to be replaced,
remove Bit Cartridge by pushing it up from the window
underneath. Replace the Bits with the desired Bits.
Ensure the Bits are properly positioned in the Cartridge
and are not protruding from the back of the Bit Cartridge.
Or, simply pull a Bit from the holder, and replace it
with the desired Bit. It will load into the Cartridge
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX254 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX254 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info