Manual Worx WX23AG.1 (page 12 of 156) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

575104

Zoom out

Zoom in

1/156

Angle grinder EN

1312

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the

instruction book carefully.

INTENDED USE

The machine is intended for cutting,

roughing and brushing metal and stone

materials without using water. For cutting

metal, a special protection guard for cutting

(accessory) must be used.

1. LOCK-OFF & LOCK-ON SWITCH

(See Fig. A)

Your switch is locked off to prevent accidental

starting. To switch on your tool, push the

safety switch lever (B) forward and depress

on/off switch (A) fully. Now your tool is switch

on. To switch off your tool, just release the On/

Off switch.

If you wish to use the tool continuously,

push the safety switch lever (B) forward and

depress on/off switch (A) fully, then push

the safety switch lever (B) forward again and

release the On/Off switch. Now your switch

has been locked on for continuously use.

To switch off your tool, simply depress On/

Off switch fully, the safety On/Off switch will

automatically release.

Restarting protection

The restarting protection feature prevents

uncontrolled restarting of the machine after an

interruption in the power supply.

To restart the operation, switch the On/Off

switch (A) to the Off position and start the

machine again.

2. HAND GRIP AREAS

Always hold your angle grinder ﬁrmly with

both hands when operating (See Fig. B).

3. ANTI-VIBRATION AUXILIARY HANDLE

This front handle incorporates a ﬂexible

vibration absorbing mounting between the

bolt and handle grip to reduce vibration and

increase comfort.

NOTE: the handle ﬁxing to the gear case is

ﬂexible and not a rigid clamp. You have the

option of three working positions to provide

the safest and most comfortable control of

your angle grinder (See Fig. C). Side position

for grinding and top position for cutting. The

handle is screwed clockwise into the gear case

hole (See Fig. B). Always use the auxiliary

handle.

4. SPINDLE LOCK BUTTON

Must only be used when changing a disc.

Never press when the disc is rotating!

5. DISC FITTING

The inner ﬂange (5) is located over the spindle

(6) and on the two spindle ﬂats. Locate the

disc onto the inner ﬂange and then the

outer ﬂange (7) is screwed onto the spindle.

Press the spindle lock button (4) and rotate

the spindle until it locks, then ﬁrmly tighten

the outer ﬂange using your pin spanner to

clamp the disc (See Fig.D). The pins on your

pin spanner locate in the holes on the outer

ﬂange. Check the disc rotates freely and is

securely clamped. Make a no load test run

for 30 seconds to check disc vibration and

disc run out. To remove a disc, reverse these

instructions.

6. ADJUSTABLE OUTER FLANGE

CLAMPING

The outer ﬂange (7) should be adjusted to suit

different disc thickness. For thinner cutting

or diamond discs the raised part of the outer

ﬂange is ﬁtted facing away from the disc (See

Fig. E.2). For thicker grinding discs the raised

part of the outer ﬂange is ﬁtted facing towards

the disc to provide improved support for the

disc hole (See Fig. E.1). Always ensure your

disc is securely clamped.

7. GUARD ADJUSTMENT (See Fig. F)

Before any work on the machine itself,

pull the mains plug.

For work with grinding or cutting discs,

the wheel guard must be mounted.

Wheel Guard for Grinding

The coded projection on the wheel guard (14)

ensures that only a guard that ﬁts the machine

type can be mounted.

Open the clamping lever (8). Place the wheel

guard (14) with coded projection into the

coded groove on the spindle of the machine

head and rotate to the required position

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX23AG.1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Worx WX23AG.1 Manual

Product: