575006
12
Zoom out
Zoom in
Previous page
1/128
Next page
12
Lithium-Ion cordless drill/driver EN
slipping off center as the hole is started. Hold
the tool firmly and place the tip of the bit at the
point to be drilled. Depress the switch trigger
to start the tool. Move the drill bit into the
workpiece, applying only enough pressure to
keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
Tungsten carbide drill bits should
always be used for concrete and
masonry. When drilling in metal, only use
HSS drill bits in good condition. Always
use a magnetic bit holder (not included)
when using short screwdriver bits. When
screw-driving, apply a small quantity of
liquid soap or similar to the screw
threads to ease insertion.
10. DISPOSAL OF AN EXHAUSTED
BATTERY PACK
To preserve natural resources, please
recycle or dispose of the battery pack
properly. This battery pack contains
Lithium batteries. Consult your local waste
authority for information regarding available
recycling and/or disposal options. Discharge
your battery pack by operating your drill, then
remove the battery pack from the drill housing
and cover the battery pack connections with
heavy-duty adhesive tape to prevent short
circuit and energy discharge. Do not attempt to
open or remove any of the components.
11. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop.
Relieve the load on the machine immediately
and allow cooling for approx. 30 seconds at
the highest no-load speed.
12. TEMPERATURE DEPENDENT
OVERLOAD PROTECTION
When using as intended for the power tool
cannot be subject to overload. When the
load is too high or the allowable battery
temperature of 75°C is exceeded, the
electronic control switches off the power
tool until the temperature is in the optimum
temperature range again.
13. PROTECTION AGAINST DEEP
DISCHARGING
The Li-Ion battery is protected against deep
discharging by the Discharging Protection
System. When the battery is empty, the
machine is switched off by means of a
protective circuit: The inserted tool no longer
rotates.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON
WHEN YOU PRESS THE SWITCH?
The forward/reverse rotation control, which is
on top of the trigger, is positioned in the lock
function. Unlock the forward/reverse rotation
control by putting it into the required rotation
position. Push the trigger and the drill will start
to rotate.
2. THE DRILL STOPS BEFORE THE SCREW
IS COMPLETELY TIGHTENED. WHY?
Verify the torque position of the torque
adjusting ring, you can find the torque-
adjusting ring between the chuck and the drill
body. Position 1 is the lowest torque (screw
driving force) and position 15 is the highest
torque (screw driving force). Position is for
drill operation. Regulate the torque adjusting
ring to a higher position to reach the best
result.
3. REASONS FOR DIFFERENT BATTERY
PACK WORKING TIMES
Charging time problems, as above, and having
not used a battery pack for a prolonged time
will reduce the battery pack working time.
This can be corrected after several charge and
discharge operations by charging & working
with your drill. Heavy working conditions such
as large screws into hard wood will use up the
battery pack energy faster than lighter working
conditions. Do not re-charge your battery pack
below 0°C and above 45°C as this will affect
performance.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX156.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX156.1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info