575006

Worx WX156.1 Manual

11
Zoom out
Zoom in
Previous page
1/128
Next page
11
Lithium-Ion cordless drill/driver EN
higher speed and torque with increased
trigger pressure. Speed is controlled by the
amount of switch trigger depression.
WARNING: Do not operate for long
periods at low speed because
excess heat will be produced internally.
2. SWITCH LOCK
The switch trigger can be locked in the OFF
position. This helps to reduce the possibility of
accidental starting when not in use. To lock the
switch trigger, place the rotation control in the
center position.
3. REVERSIBLE (See Fig. C1, C2)
For drilling and screw driving use forward
rotation marked “ ” (lever is moved to the
left). Only use reverse rotation marked “ ”
(lever is moved to the right) to remove screws
or release a jammed drill bit.
WARNING: Never change the
direction of rotation when the
chuck is rotating, wait until it has
stopped!
4. TWO-SPEED GEAR CONTROL
(See Fig. D)
The drill has a two-speed gear control
designed for drilling or driving at LO (mark is
1) or HI (mark is 2) speeds. A slide switch is
located on top of the drill to select either LO
or HI speed. When using the drill in the LO
speed range, the speed will decrease and the
drill will have greater power and torque. When
using the drill in the HI speed range, the speed
will increase and the drill will have less power
and torque.
Gear I
Low speed range: For screwdriving or working
with large drilling diameter.
Gear II
High speed range: For working with small
drilling diameter.
WARNING: To prevent gear damage,
always allow the chuck to come to
a complete stop before changing the
direction of rotation or the two-speed
gear control.
5. CHUCK ADJUSTMENT (See Fig. E)
To open the chuck jaws rotate the front section
of the chuck. Insert the drill bit between the
chuck jaws and rotate the front section in the
opposite direction. Ensure the drill bit is in
the center of the chuck jaws. Finally, firmly
rotate the front chuck section in the opposite
directions. Your drill bit is now clamped in the
chuck.
6. TORQUE ADJUSTMENT (See Fig. F)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the torque
adjustment ring. The torque is greater when
the torque adjustment ring is set on a higher
setting. The torque is less when the torque
adjustment ring is set on a lower setting.
Make the setting as follows:
1 - 4 For driving small screws
5 - 9 For driving screws into soft
material
10 - 15 For driving screws into soft and
hard material
For heavy drilling
7. AUTOMATIC SPINDLE LOCK
(See Fig. G)
The automatic spindle lock allows you to use
it as a regular screwdriver. You can give an
extra twist to firmly tighten a screw, loosen
a very tight screw or continue working
when the battery energy has expired. For
manual screwdriver purposes, the chuck is
automatically locked when the tool is off.
8. USING THE SIGHT LIGHT
To turn on the light simply press the on/off
switch. When you release the on/off switch,
the light will be off.
LED lighting increases visibility-great for
dark or enclosed area. LED is also a battery
capacity indicator. It will flash when power
gets low.
9. DRILLING
When drilling into a hard smooth surface,
use a center punch to mark the desired hole
location. This will prevent the drill bit from
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WX156.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WX156.1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info