578151
11
Zoom out
Zoom in
Previous page
1/144
Next page
Lawn Mowing Robot EN
11
4. Boundary Wire Basics
4.1 Pegging the Boundary Wire
Use the Boundary Wire Distance Gauge (24) to set the correct
distance from the border of your lawn (More than 35cm *).
* This is the recommended distance. Use the provided distance
gauge to ensure proper installation.
If your neighbor also uses a Landroid
®
M, then you must keep a
spacing of at least 2 metres between your Boundary Wire and your
neighbors.
Please be aware that your Landroid
®
M will not be able to receive a
signal from the Boundary Wire beyond the distance of 18m.
The boundary wire must outline the intended mowing area
exactly.
Your Landroid
®
M will become confused by extra bends or coils of Boundary Wire that are not part of its mowing
area ( See Fig. H). If there is excess Boundary Wire after the mowing area has been outlined, then cut it off and store
this additional wire in a separate location. However, it is important to leave the necessary length where it connects to the
Charging Base so it can be connected and still remain buried.
4.2 Burying the Boundary Wire
If you are planning to bury the Boundary Wire then it should be noted that when entering its Charging Base for the first time,
your Landroid
®
M may find problems with the way you have laid the wire. It is recommended to first peg down the Boundary
Wire to the lawn so it is easy to make adjustments if necessary. This will allow the Landroid
®
M to become adjusted to its new
environment and ensures it will successfully work with the charging base before the Boundary Wire is buried.
When you have completed installing the boundary wire, it is recommended that you ask Landroid
®
M to follow the boundary
wire by pressing the home button.
Whilst observing Landroid
®
M locating the charging station you can then make alterations to the boundary wire route to
ensure trouble free tracking of the boundary wire by Landroid
®
M when locating the charging station.
4.3 Joining the Boundary Wire
The Boundary Wire (21) can be extended simply by splicing the ends
and connecting it to the ends of another piece of wire. You can use
insulating tape to secure the joined part of the wire. (See Fig. I)
4.4 Turn on and test installation
If the charger base LED does not come on, then check the power
connections.
If the charger base LED is flashing green, check if the boundary wire
is connected correctly.
Red light on: charging.
Red light flashing: error message, refer to Trouble Shooting and
correct the problems.
Green light flashing: check if the boundary wire is connected correctly.
When the green light on the charging base is on, place your Landroid
®
M over the boundary wire, if Landroid
®
M follows the
boundary it is connected correctly.
If your Landroid
®
M is inside its territory but the display says “Outside working area” ,and the charger
base LED is green, it means you clamped the boundary wire ends incorrectly. Just reverse them.
H
I
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WG791E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WG791E in the language / languages: English, German, Danish, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 23,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Worx WG791E

Worx WG791E Installation Guide - English, German - 144 pages

Worx WG791E Installation Guide - Dutch - 20 pages

Worx WG791E User Manual - Dutch - 16 pages

Worx WG791E Installation Guide - Danish, French, Italian, Polish, Portuguese, Spanish - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info