576045

Worx WG368E.9 Manual

19
Zoom out
Zoom in
Previous page
1/204
Next page
Cordless Chain Saw EN
19
SAW MAINTENANCE AND
KICKBACK SAFETY
Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and guide bar
maintenance can reduce chances of kickback.
Inspect and maintain saw after each use. This
will increase the service life of your saw.
NOTE: Even with proper sharpening, risk of
kickback can increase with each sharpening.
MAINTENANCE AND
STORAGE OF CHAIN SAW
1. Remove the battery pack from the saw
• When not in use.
• Before moving from one place to another
• Before servicing.
• Before changing accessories or attachments,
such as saw chain and guard bar.
2. Inspect chain saw before and after each
use. Check saw closely if guard or other part
has been damaged. Check for any damage
that may affect operator safety or operation
of saw. Check for alignment or binding of
moving parts. Check for broken or damaged
parts. Do not use chain saw if damage affects
safety or operation. Have damage repaired
by authorized service center. To locate an
authorized service center, visit
www.worx.com
3. Maintain chain saw with care.
• Never expose saw to rain.
• Keep chain sharp, clean, and lubricated for
better and safer performance.
• Follow steps outlined in this manual to
sharpen chain.
• Keep handles dry, clean, and free of oil and
grease.
• Keep all screws and nuts tight.
4. When servicing, use only identical
replacement parts.
5. When not in use, always store chain saw
• In a high or locked place, out of children’s
reach.
• In a dry place.
BAR MAINTENANCE
To maximize bar life, the following bar
maintenance is recommended.
The bar rails that carry the chain should be
cleaned before storing the tool or if the bar or
chain appear to be dirty.
The rails should be cleaned every time the
chain is removed.
Turn the bar over, top rail becoming bottom
and bottom rail becoming top, around every 5
hours of use.
TO CLEAN THE BAR RAILS:
1. Remove chain cover and bar and chain.
(see section ASSEMBLY)
2. Using a wire brush, screwdriver or similar
suitable tool, clear the residue from the
rails of the bar. (See Fig. V)
3. Make sure to clean oil passages
thoroughly.
CONDITIONS WHICH REQUIRE GUIDE
BAR MAINTENANCE:
• Saw cuts to one side or at an angle.
• Saw has to be forced through the cut.
• Inadequate supply of oil to the bar and
chain.
Check the condition of the guide bar each time
the chain is sharpened. A worn guide bar will
damage the chain and make cutting difficult.
After each use, with unit disconnected from
power source, clean all sawdust from the
guide bar and sprocket hole.
When rail top is uneven, use a flat file to
restore square edges and sides.
File Rail Edges
and Sides
Square
Worn Groove Correct Groove
Replace the guide bar when the groove is
worn, the guide bar is bent or cracked, or
when excess heating or burring of the rails
occurs. If replacement is necessary, use only
the guide bar specified for your saw in the
repair parts list or on the decal located
on the chain saw.
REPLACING BAR & CHAIN
Fit the chain and guide bar as described in
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Worx WG368E.9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Worx WG368E.9 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 8,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info