724651
10
Zoom out
Zoom in
Previous page
1/18
Next page
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018
18 19
4. To remove the battery pack (6) from the
charger (7), press the battery release button
on the battery pack (6) and slide away from
the charger in the reverse direction it was
installed into the charger (7) (Fig C).
NOTE: For any issues related directly to
your purchased ALDI Xnity Battery /
charger, contact the Customer Service of
the manufacturer as listed on the battery /
charger packaging, manual or on the label
on the battery / charger.
Fitting the Belt Hook
NOTE: Ensure the battery is not installed or
the drill operational when tting the belt
hook.
1. Align the ridge on the back of belt hook (3)
into the groove on the side of the Impact
wrench. Insert the assembly screw through
the belt hook screw hole and using a Philips
head screwdriver, tighten the screw by turning
in a clockwise direction (Fig D).
D.
Operation
Inserting and removing Sockets
1. Align an appropriate ½ “ socket with the
½ “ square drive (1)
2. Push the socket on to the square drive shaft
until it clicks into place.
2. To remove the socket from the square drive
shaft, simply pull it away from the square
drive shaft (Fig E).
Forward/Reverse Switch
NOTE: You can only change the direction
of rotation of the impact wrench using the
forward/reverse selector (2) when the trigger
switch (5) is NOT depressed.
This selector will allow you to change the
direction of the motor while the trigger switch
(5) is not depressed.
1. To put in reverse mode, push in the forward/
reverse selector (2) on the side of the drill
where the arrow on the switch is pointing to
the rear end of the drill. The chuck will rotate
in an anti-clockwise direction (Fig F).
The reverse mode is intended for the removal
of screws and bolts.
2. To put in forward mode, push in the forward/
reverse selector (2) on the side of the drill
where the arrow on the switch is pointing to
the front end of the drill. The chuck will rotate
in an clockwise direction (Fig G).
The forward mode is for fastening screws
and bolts.
E.
INSTALL
REMOVE
F.
G.
C.
INSTALL
REMOVE
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone IW36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone IW36 in the language / languages: English as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info