724651

Workzone IW36 Manual

11
Zoom out
Zoom in
Previous page
1/18
Next page
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018
AFTER SALES SUPPORTe-mail: help@powertoolsupport.com
1800 909 909 (toll free)MODEL No.: IW36 • 61551 • 07/2018
20 21
Using the Trigger switch
This trigger switch (5) is an electronic variable
speed control which enables the user to vary
the speed continuously.
1. After selecting the direction of rotation using
the forward/reverse selector (2) and installing
the socket required for the work task at hand,
pressing on the trigger switch (5) will then
activate the impact wrench for use (Fig H).
2. The speed varies according to how far the trigger switch (5) is depressed.
The further it is depressed the faster the socket will rotate; the lighter it is
depressed, the slower it will rotate.
Fastening / Removing Screws, Nuts & Bolts
NOTE: When tightening a nut or a bolt always
start the fastener by hand by 2 or 3 threads
BEFORE using the impact wrench.
NOTE: The longer the impact wrench is operated
in the hammer function, the tighter the fastener
will become. 1 –2 seconds is normally sucient
with small nuts, and bolts even less time.
1. Select the appropriate forward or reverse
function using the selector (2).
2. Insert the socket onto the ½ “ square drive shaft (1).
3. Ensure your work piece (if applicable) is secured in position to stop it
moving whilst fastening or removing screws or bolts.
4. Hold the socket rmly against the bolt or screw to ensure it does not
slip (Fig I).
5. Slowly increase the pressure on the trigger switch (5) until you reach the
appropriate torque required for the fastening or removal of the screw or
bolt.
H.
I.
J.
NOTE: Do not over tighten. Studs can break, threads stripped or threads
stretched where fasteners are over tightened.
NOTE: Always check the nut or bolt after tightening with the impact
wrench, the fastener is secure by a manual operation. i.e using a spanner or
wheel brace
IMPORTANT: If the impact wrench is used to secure and tighten wheel
nuts, ensure the nuts are manually checked with a hand brace after using
the brace.
Using the LED worklight
1. When the unit is switched (the trigger switch
(5) is depressed) , the LED work light (4) also
comes on to ensure better vision and to make
working in dark areas more safe (Fig I).
The working light goes out when the trigger
switch (5) is released.
CAUTION! LED is laser class 1!
Do not look directly into the laser as this may
result in damage to the eyes.
Operating tips
You will extend the life of your sockets/bits and do neater work if you
always put the socket/bits in contact with the work before pulling the
trigger switch (5). During the operation, hold the Impact Wrench rmly
and exert light, steady pressure. Too much pressure at low speed will stall
the Impact Wrench . Too little pressure will allow the driver socket/bit to
disengage from the fastener and damage the fastener head and driver bit.
Always use a good quality driver bit which matches the screw head
correctly. When using a at driver bit ensure a correct t between the
fastener and bit and it is recommended to use a bit with a sleeved guide.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone IW36 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone IW36 in the language / languages: English as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info