724636
17
Zoom out
Zoom in
Previous page
1/21
Next page
Digital Inverter Generator with Pure Sine Wave
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. EP2800i • 09/2018 • 62007
(toll free)
AFTER SALES SUPPORT
(toll free)
Digital Inverter Generator with Pure Sine Wave
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. EP2800i • 09/2018 • 62007
30 31
Maintenance Maintenance
Fuel Tank Inlet Filter
WARNING: Ensure the engine is switched o while undertaking
this task.
1. Turn the fuel tap/ lever (23) to the o position (Fig AC).
3. The fuel tank inlet lter (24) is located directly under the fuel tank cap
(27) and protects impurities entering the fuel tank (26) during refuelling.
Remove the fuel tank cap (27) by turning in an anti-clockwise direction
(Fig AD).
4. Remove the fuel tank inlet lter (24) (Fig AE) and wash thoroughly
in petrol.
5. Re-assemble by putting the fuel tank inlet lter (24) back, and then
securing the fuel tank cap (27) in a clockwise direction until rmly
secured.
Fuel extension lter
A small fuel extension lter (22) has been tted to the inlet side of the fuel
lever tap (23), inside the tank. This fuel extension lter (22) prevents any dirt
in the fuel from entering the fuel system. The procedure for removing this
lter is as per follows:
NOTE: the following procedure should be performed in a well ventilated
area, with no naked ames, sparks, or cigarettes. Safety glasses should also
be worn and both the engine on/o switch (2), and the 240Va.c Outlet
power on/o switch (1) need to be in the OFF position.
Air Filter
It is very important to maintain an air lter (18) in proper condition. Damage to
the generator may arise if the lter has:
Improperly been serviced.
Dirt and other foreign elements adhering to the lter due to improper
installation and engine wear.
It is recommended the air lter (18) is cleaned every 50 hours (every 10 hours
under dusty conditions).
ALWAYS keep the lter clean at all times.
WARNING: Ensure the engine is switched o while undertaking this task.
1. Remove the air lter cover (17) on the side of the generator using the
supplied screwdriver (31) by removing (unscrewing) the two screws on the
face of the cover, in an anti-clockwise direction (Fig AA).
2. Remove the air lter (18) (Fig AB).
3. Wash the air lter (18) in hot soapy water and allow to dry.
4. Lubricate the air lter (18) using a small amount of engine oil (SAE 10W-30).
5. Thoroughly squeeze the air lter (18) removing any excess oil.
6. Replace the air lter (18).
7. Secure the air lter cover (17) back on to the side panel of the air lter
housing using the supplied screwdriver (31) by screwing back in the two
screws in a clockwise direction until secure.
IMPORTANT. Never run the engine without the air lter element in place.
CAUTION: Never use fuel or low burning paint solvents to clean the air lter
(18). A re or explosion could result.
CAUTION: Ensure the air lter (18) is dry before re tting.
Replacement air lters are available from https://help.tools/ or by calling
Customer Service on
1800 909 909.
AE.AD.
AC.
ON
OFF
AB.
AA.
LOOSEN
TIGHTEN
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone EP2800i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone EP2800i in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info