724636

Workzone EP2800i Manual

14
Zoom out
Zoom in
Previous page
1/21
Next page
Digital Inverter Generator with Pure Sine Wave
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. EP2800i • 09/2018 • 62007
(toll free)
AFTER SALES SUPPORT
(toll free)
Digital Inverter Generator with Pure Sine Wave
e-mail: help@powertoolsupport.com1800 909 909
MODEL: №. EP2800i • 09/2018 • 62007
24 25
Normal procedure for Stopping the Engine
(Full shut down and Store)
1.  Turn “OFF” the 240Va.c Outlet Power On/O switch (1) by pushing the
switch to the right hand side. (Fig U).
2. Remove any appliances connected to either of the 2 outlets (Fig K).
3. Allow the engine to slow down and idle for approx 15-30 seconds.
4. Press the engine On/O switch (2) to the “OFF” position as indicated
by an “O” (Fig. V). The unit will stop running .
5.  Turn the fuel lever / tap (23) anti clockwise to the “OFF” position (Fig. W)
Overload procedure for restarting and resetting the engine
1. Turn “OFF” the 240Va.c Outlet Power On/O switch (1) by pushing the
switch to the right hand side. (Fig U).
2. Allow the engine to slow down and idle for approximately 15-30 seconds.
Remove any appliances connected to either of the 2 AC sockets.
3. Press the engine On/O switch (2) to the “OFF” position as indicated by an
“O”(Fig. X). The unit will stop
running and is shut down.
Now follow the normal starting
procedure to restart the generator.
WARNING: All appliances are rated dierently. This generator will work
only with Australian approved rated appliances with an input voltage of
220-240Va.c (Fig T). Check your appliances meet this requirement on its
rating label before using them. In simple terms if you cant use the product
in your home you denitely cannot use it on this generator.
Overload condition ( Where the appliances want more
power then the generator can provide)
Once operating, If the AC side of the generator becomes overloaded , the
red load status indicator (5) LED will illuminate. The generator will continue
to supply 240Va.c output for a very short time, but if the load is not reduced,
the 240V supply will be automatically shut down. To reduce load rstly
you can stop using one appliance and turn it o , see if that recties the
problem. If not refer to page 15 on loading’s and how they work. If this does
NOT solve your problem, or you do not reduce load fast enough, the output
of the generator will be automatically shut down, and the petrol motor
will continue to run. You will now need to reset the overload condition by
shutting down the petrol motor (Fig S), and thus restart the engine after the
load being applied to the generator has been reduced. Refer to the Overload
procedure for re-starting and re-setting the engine. Always connect the
largest appliance you want to run rst allowing it time to draw current to
start . After 20-30 seconds connect the second appliance.
T.
Operation Operation
X.
OFF
V.U. W.
ON
OFF
OFF
OFF
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone EP2800i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone EP2800i in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info