724628
11
Zoom out
Zoom in
Previous page
1/19
Next page
AFTER SALES SUPPORT e-mail: info.aldi@positecgroup.com
1300 889 028 (toll free) MODEL No.: CS20V • 63350 • 01/2019
AFTER SALES SUPPORT
1300 889 028 (toll free) e-mail: info.aldi@positecgroup.com
MODEL No.: CS207 • 63350 • 01/2019
20 21
10. Operation
Adjusting the Cutting Depth
WARNING:
battery (27) is removed before making any adjustments.
1. Ensure that the saw is facing away from you.
2. Loosen the depth locking lever (18) (Fig D).
3.
body of the saw until the blade is at the right depth (Fig E). Use the depth of
cut indicator (19) to determine the cutting depth.
4. Tighten the depth locking lever (18).
NOTE: Always use the correct blade depth setting. The correct blade depth
setting for all cuts should not be more than (6.35mm) 1/4” below the material
being cut. Allowing more depth will increase the chance of kickback and result
in a rough cut.
D.
H.
F.
E.
I. J.
G.
2. Loosen the bevel adjustment knob (9) located at the front of the base plate (15)
(Fig G).
3. Tilt the body of the saw until the required angle is reached using the bevel scale
(10) as a guide (Fig H).
4. Tighten the bevel adjustment knob (9) to secure the base plate (15) (Fig I).
NOTE: Always make a trial cut in a scrap piece of material along a guideline to
an accurate cut.
1. Attach the battery pack (27) to the circular saw.
2.
3. The blade will take approximately 2 seconds to reach full speed.
4.
re-engages to prevent accidental operation.
CAUTION: Allow the blade (21) to come to a complete standstill before setting
the saw down.
Adjusting the Bevel Angle
WARNING:
is removed before making any adjustments.
1. The circular saw can be adjusted to cut at any angle between 0° and 50°. When
making 45° bevel cuts, there is a blade guide notch (22) on the circular saw
base to help you line up the blade with the line of cut (Fig F). Align your line
of cut with the inner blade guide notch on the base of the circular saw when
making 45° bevel cuts. TIGHTEN
LOOSEN
2
1
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Workzone CS20V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Workzone CS20V in the language / languages: English as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info